CloudsService.apk
06ab80c8.0
checkota.sh
libshellcmd.so
shell_cmd_service

а в ините прописаны запуски
#clouds checkota service
service checkota /system/bin/checkota.sh
class main
oneshot

#clouds ota service
service shcmd /system/bin/shell_cmd_service
class main

#!/system/bin/sh
OTA_APK="/system/app/CloudsService.apk"
OTA_MD5="00a46780cb123dff97eb98cd080f5a0e"
mount -o remount,rw /system
if [ ! -f "$OTA_APK" ]; then
/system/bin/cp /cloudsota/CloudsService.apk /system/app/
/system/bin/chmod 644 /system/app/CloudsService.apk
else
echo "the same apk"
# /system/bin/mkdir /data/CloudsService
# TMP_MD5=`/system/bin/busybox md5sum /system/app/CloudsService.apk | /system/bin/busybox cut -d " " -f 1`
# if [ $OTA_MD5 = $TMP_MD5 ]; then
# echo "the same apk"
# else
# echo "not the same apk"
# /system/bin/cp /cloudsota/CloudsService.apk /system/app/
# /system/bin/chmod 644 /system/CloudsService.apk
# fi
fi

su
mount -o remount,rw /system
rm /system/bin/checkota.sh
rm /system/etc/CloudsService.apk
rm /system/app/CloudsService.apk
вот статейка

[wifi_para]
wifi_used = 1
wifi_sdc_id = 1
wifi_usbc_id = 1
wifi_usbc_type = 1
wifi_mod_sel = 8
wifi_power = "axp22_dldo1"
wifi_power_ext1 = "axp22_dldo2"
wifi_power_ext2 = ""
wifi_power_switch = port:power0<1><0><default><0>

rtl8723bs_wl_regon = port:PL06<1><default><default><0>
rtl8723bs_wl_host_wake = port:PL07<4><default><default><0>
rtl8723bs_bt_regon = port:PL08<1><default><default><0>
rtl8723bs_bt_wake = port:PL10<1><default><default><0>
rtl8723bs_bt_host_wake = port:PL09<4><default><default><0>
rtl8723bs_lpo_use_apclk = 0

rtl8189es_shdn = port:PL06<1><default><default><0>
rtl8189es_host_wake = port:PL07<4><default><default><0>

[partition]
name = private
size = 32768
user_type = 0x8000

Почитав форумы и спецификации подобных контроллеров понял, что его надо сбросить, берем металлический пинцет с тонкими ножками и правый контакт батареи соединяем на некоторое время в обход контроллера прямо на корпус. Им может быть любой металлический экран на плате, на всякий случай предварительно прозвонив мультиметром соединен ли он с общей шиной.

Одновременно зажимаем кнопку "включить" и устройство влючается – пинцет можно убирать, теперь контроллер на материнке и батареи поняли, что надо работать и считывают состояние батареи как положенно. Батарею (сам планшет) нужно зарядить до максимума хорошей зарядкой (у меня 5 В 2100 мА) и можно использовать.

если + закоротить на корпус(шину), бет короткое замыкание и контролер с планшетом сгорит.

; CAMERA_FACING_BACK
; gc2035

; CAMERA_FACING_FRONT
; gc0307

vip_dev0_mname = "gc2035"
vip_dev0_twi_id = 0
vip_dev0_twi_addr = 0x78
vip_dev0_isp_used = 0
vip_dev0_fmt = 0
vip_dev0_stby_mode = 0
vip_dev0_vflip = 0
vip_dev0_hflip = 0
vip_dev0_iovdd = "axp22_dldo3"
vip_dev0_iovdd_vol = 2800000
vip_dev0_avdd = "axp22_dldo4"
vip_dev0_avdd_vol = 2800000
vip_dev0_dvdd = "axp22_eldo2"
vip_dev0_dvdd_vol = 1500000
vip_dev0_afvdd = ""
vip_dev0_afvdd_vol = 2800000
vip_dev0_power_en =
vip_dev0_reset = port:PE06<1><default><default><0>
vip_dev0_pwdn = port:PE05<1><default><default><1>
vip_dev0_flash_en =
vip_dev0_flash_mode =
vip_dev0_af_pwdn =

vip_dev0_mname = "gc2035"
vip_dev0_twi_id = 0
vip_dev0_twi_addr = 0x88
vip_dev0_isp_used = 0
vip_dev0_fmt = 0
vip_dev0_stby_mode = 0
vip_dev0_vflip = 0
vip_dev0_hflip = 0
vip_dev0_iovdd = "axp22_dldo3"
vip_dev0_iovdd_vol = 2800000
vip_dev0_avdd = "axp22_ldoio0"
vip_dev0_avdd_vol = 2800000
vip_dev0_dvdd = "axp22_eldo2"
vip_dev0_dvdd_vol = 1800000
vip_dev0_afvdd = ""
vip_dev0_afvdd_vol = 2800000
vip_dev0_power_en =
vip_dev0_reset = port:PE04<1><default><default><0>
vip_dev0_pwdn = port:PE05<1><default><default><1>
vip_dev0_flash_en =
vip_dev0_flash_mode =
vip_dev0_af_pwdn =

или глянуть на какой там прошивке были камеры =ь

[csi0]

vip_used = 1
vip_mode = 0
vip_dev_qty = 2
vip_define_sensor_list = 0
vip_csi_pck = port:PE00<2><default><default><default>
vip_csi_mck = port:PE01<2><default><default><default>
vip_csi_hsync = port:PE02<2><default><default><default>
vip_csi_vsync = port:PE03<2><default><default><default>
vip_csi_d0 = port:PE04<2><default><default><default>
vip_csi_d1 = port:PE05<2><default><default><default>
vip_csi_d2 = port:PE06<2><default><default><default>
vip_csi_d3 = port:PE07<2><default><default><default>
vip_csi_d4 = port:PE08<2><default><default><default>
vip_csi_d5 = port:PE09<2><default><default><default>
vip_csi_d6 = port:PE10<2><default><default><default>
vip_csi_d7 = port:PE11<2><default><default><default>

vip_dev0_mname = "gc2035"
vip_dev0_pos = "rear"
vip_dev0_lane = 1
vip_dev0_twi_id = 2
vip_dev0_twi_addr = 0x78
vip_dev0_isp_used = 0
vip_dev0_fmt = 0
vip_dev0_stby_mode = 0
vip_dev0_vflip = 0
vip_dev0_hflip = 0
vip_dev0_iovdd = "axp22_dldo3"
vip_dev0_iovdd_vol = 2800000
vip_dev0_avdd = "axp22_ldoio0"
vip_dev0_avdd_vol = 2800000
vip_dev0_dvdd = "axp22_eldo2"
vip_dev0_dvdd_vol = 1800000
vip_dev0_afvdd = "axp22_eldo3"
vip_dev0_afvdd_vol = 2800000
vip_dev0_power_en =
vip_dev0_reset = port:PE16<1><default><default><0>
vip_dev0_pwdn = port:PE15<1><default><default><1>
vip_dev0_flash_en =
vip_dev0_flash_mode =
vip_dev0_af_pwdn =


vip_dev1_mname = "gc0308"
vip_dev1_pos = "front"
vip_dev1_lane = 1
vip_dev1_twi_id = 2
vip_dev1_twi_addr = 0x42
vip_dev1_isp_used = 0
vip_dev1_fmt = 0
vip_dev1_stby_mode = 0
vip_dev1_vflip = 0
vip_dev1_hflip = 0
vip_dev1_iovdd = "axp22_dldo3"
vip_dev1_iovdd_vol = 2800000
vip_dev1_avdd = "axp22_ldoio0"
vip_dev1_avdd_vol = 2800000
vip_dev1_dvdd = "axp22_eldo2"
vip_dev1_dvdd_vol = 1800000
vip_dev1_afvdd = "axp22_eldo3"
vip_dev1_afvdd_vol = 2800000
vip_dev1_power_en =
vip_dev1_reset = port:PE16<1><default><default><0>
vip_dev1_pwdn = port:PE17<1><default><default><1>
vip_dev1_flash_en =
vip_dev1_flash_mode =
vip_dev1_af_pwdn =

;--------------------------------------------------------------------------
[camera_list_para]
camera_list_para_used = 1
ov7670 = 0
hi704 = 0
mt9m112 = 0
mt9m113 = 0
ov2655 = 0
hi253 = 0
gc0307 = 0
mt9d112 = 0
ov5647 = 0
gc2015 = 0
ov2643 = 0
tvp5150 = 0
s5k4ec = 0
ov5650_mv9335 = 0
;-----------------------0.3M---------------------------------------------
siv120d = 1
siv121d = 1
gc0309 = 1
gc0308 = 1
gc0311 = 1
gc0328 = 1
gc0329 = 1
sp0838 = 1
sp0718 = 1
sp0a19 = 1
bf3a03 = 1
bf3703 = 1
;-----------------------2M---------------------------------------------
sp2518 = 1
gc2035 = 1
gc2155 = 1
gc2145 = 1
bf3920 = 1
st25a = 1
gt2005 = 1
;-----------------------5M---------------------------------------------
ov5640 = 1

Способ, как откалибровать батарею на Андроиде, предложенный компанией Google, достаточно сложен. Судите сами:

1.Зарядить планшет или смартфон. Процесс должен идти как минимум 8 часов, даже если система сигнализирует, что зарядка окончена. Устройство при этом должно быть включено.

2.Отсоединить зарядное или вытащить его из розетки. Выключить планшет или смартфон.

3.Снова начать процесс зарядки и продолжать его в течение часа.

4.Отключить зарядник и включить планшет или смартфон. Продержать его в таком состоянии минуту или две.

5.Выключить устройство и снова произвести зарядку. Продолжать на протяжении часа.

6.Физически отсоединить кабель зарядного устройства и включить смартфон или планшет.

Выглядит на первый взгляд странно. Но все рационально и просто. Таким образом пересоздаётся статистика и максимально подгоняются параметры аппаратной части под все условия. С физической точки зрения все выглядит так: после первого пункта аккумулятор набирает ёмкость, которая соответствуют максимальным показаниям контроллера, записанным в системной статистике; второй пункт снимает нагрузку, отключены все потребители; третий пункт производит дозарядку с оптимальным током и напряжением под аппаратным контролем микросхемы питания; четвёртый пункт заставляет систему обновить статистику, поскольку показания датчиков могут не соответствовать ранее записанным; Действия пятого и шестого пункта — контрольные. Предназначены они в основном для сложных устройств, у которых системы управления питания пользуются данными статистики операционной системы. Последние два действия позволяют действительно зарядить батарею полностью. И включение смартфона или планшета вновь записывает новый максимум показателей в статистику, если они изменились. Как видно, это самый действенный метод, можно производить его периодически, если батарея теряет ёмкость.

pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 0
pmu_bat_para5 = 0
pmu_bat_para6 = 0
pmu_bat_para7 = 0
pmu_bat_para8 = 0
pmu_bat_para9 = 1
pmu_bat_para10 = 2
pmu_bat_para11 = 3
pmu_bat_para12 = 5
pmu_bat_para13 = 10
pmu_bat_para14 = 16
pmu_bat_para15 = 31
pmu_bat_para16 = 43
pmu_bat_para17 = 49
pmu_bat_para18 = 53
pmu_bat_para19 = 57
pmu_bat_para20 = 60
pmu_bat_para21 = 63
pmu_bat_para22 = 66
pmu_bat_para23 = 71
pmu_bat_para24 = 77
pmu_bat_para25 = 80
pmu_bat_para26 = 84
pmu_bat_para27 = 88
pmu_bat_para28 = 92
pmu_bat_para29 = 94
pmu_bat_para30 = 96
pmu_bat_para31 = 98
pmu_bat_para32 = 100

mkdir /mnt/sdcard/nanda
mount -t vfat /dev/block/nanda /mnt/sdcard/nanda
скопируй скрипт бин с sdcard/nanda на комп и выйди с папки, и вводи следующее
umount /mnt/sdcard/nanda

adb shell "cat /dev/block/nandb > /mnt/sdcard/nandb; sync"
echo nandb_env
adb shell "cat /dev/block/nandc > /mnt/sdcard/nandc; sync"
echo nandc_boot
adb shell "cat /dev/block/nandd > /mnt/sdcard/nandd; sync"
echo nandd_system
adb shell "cat /dev/block/nande > /mnt/sdcard/nande; sync"
echo nande_data
adb shell "cat /dev/block/nandf > /mnt/sdcard/nandf; sync"
echo nandf_misc
adb shell "cat /dev/block/nandg > /mnt/sdcard/nandg; sync"
echo nandg_recovery
adb shell "cat /dev/block/nandh > /mnt/sdcard/nandh; sync"
echo nandh_cache
adb shell "cat /dev/block/nandj > /mnt/sdcard/nandj; sync"
echo nandj_private
adb shell "cat /dev/block/nandk > /mnt/sdcard/nandk; sync"
echo nandk_UDISK

cat /dev/block/nanda > /mnt/sdcard/nanda; sync

;A33 Y3 7.85" lcd panel board application
; the difference between Y2 and Y3:
; wifi/bt dram nand
; Y2 AP6210 SKHYNIX MICRON MLC
; Y3 rtl8723bs MIRA TOSHIBA MLC
;---------------------------------------------------------------------------------------------------------
; port configuration:
; port_name = port:GPIO<mux><pull up/down><driver level><default value>
; mux: GPIO function configuration, 0-input, 1-output, 2+: special funciton for modules
; pull up/down: 1-pull up, 2-pull down
; driver level: 0,1,2,3. 2 is recommended
; default value: default output value when this IO is configured as an output IO
;---------------------------------------------------------------------------------------------------------

[product]
version = "100"
machine = "evb"

;---------------------------------------------------------------------------------------------------------
; eraseflag - 1 erase data partition, 0 - do not erase data partition
; next_work - action after burn, 0x0 by config, 0x1, normal, 0x2 reboot 0x3 ,shutdown,0x4 reupdate ,0x5 boot
;---------------------------------------------------------------------------------------------------------
[platform]
eraseflag = 1
next_work = 0

;----------------------------------------------------------------------------------
;[target] system bootup configuration
;boot_clock = CPU boot frequency, Unit: MHz
;storage_type = boot medium, 0-nand, 1-card0, 2-card2, -1(defualt)auto scan
;----------------------------------------------------------------------------------
[target]
boot_clock = 1008
storage_type = -1

;---------------------------------------------------------------------------------
; uboot key detect enable
; 当keyen_flag = 1 时，支持按键检测
; 当keyen_flag = 0 时，不支持
;---------------------------------------------------------------------------------
[key_detect_en]
keyen_flag = 1

;----------------------------------------------------------------------------------
;dcdc1_vol ---set dcdc1 voltage,mV,1600-3400,100mV/step
;dcdc2_vol ---set dcdc2 voltage,mV,600-1540,20mV/step
;dcdc3_vol ---set dcdc3 voltage,mV,600-1860,20mV/step
;dcdc4_vol ---set dcdc4 voltage,mV,600-1540,20mV/step
;dcdc5_vol ---set dcdc5 voltage,mV,1000-2550,50mV/step
;aldo2_vol ---set aldo2 voltage,mV,700-3300,100mV/step
;aldo3_vol ---set aldo3 voltage,mV,700-3300,100mV/step
;----------------------------------------------------------------------------------
[power_sply]
dcdc1_vol = 3000
dcdc2_vol = 1100
dcdc3_vol = 1200
dcdc4_vol = 0
dcdc5_vol = 1500
aldo2_vol = 2500
aldo3_vol = 3000

;----------------------------------------------------------------------------------
;card boot
;----------------------------------------------------------------------------------
[card_boot]
logical_start = 40960
sprite_gpio0 =

;----------------------------------------------------------------------------------
;[cardx_boot_para] boot card configuration
;card_ctrl = boot card NO. 0 or 2
;card_high_speed = speed mode, 0-normal mode(up to 25MHz), 1-high speed mode(up to 50MHz)
;card_line = boot card buswidth(1 or 4)
;----------------------------------------------------------------------------------
[card0_boot_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF0<2><1><2><default>
sdc_d0 = port:PF1<2><1><2><default>
sdc_clk = port:PF2<2><1><2><default>
sdc_cmd = port:PF3<2><1><2><default>
sdc_d3 = port:PF4<2><1><2><default>
sdc_d2 = port:PF5<2><1><2><default>

[card2_boot_para]
card_ctrl = 2
card_high_speed = 1
card_line = 4
sdc_2xmode = 1
sdc_clk = port:PC05<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>

;----------------------------------------------------------------------------------
;[twi_para] twi for boot code
;twi_port = twi controller ID
;----------------------------------------------------------------------------------
[twi_para]
twi_port = 0
twi_scl = port:PH02<2><default><default><default>
twi_sda = port:PH03<2><default><default><default>

;----------------------------------------------------------------------------------
;[uart_para] boot debug port configuration
;uart_debug_port = uart port ID for boot debug
;----------------------------------------------------------------------------------
[uart_para]
uart_debug_port = 0
uart_debug_tx = port:PF02<3><1><default><default>
uart_debug_rx = port:PF04<3><1><default><default>

;----------------------------------------------------------------------------------
;[jtag_para] jtag configuration
;jtag_enable = 0-disable jtag, 1-enable jtag
;----------------------------------------------------------------------------------
[jtag_para]
jtag_enable = 1
jtag_ms = port:PF00<3><default><default><default>
jtag_ck = port:PF05<3><default><default><default>
jtag_do = port:PF03<3><default><default><default>
jtag_di = port:PF01<3><default><default><default>

;----------------------------------------------------------------------------------
;[clock] pll configuration
;----------------------------------------------------------------------------------
[clock]
pll3 = 297
pll4 = 300
pll6 = 600
pll8 = 408
pll9 = 480
pll10 = 297
pll_cpupat = 0
pll_gpupat = 0xc440e666
pll_videopat = 0
pll_vepat = 0
pll_hsicpat = 0
pll_depat = 0
pll_mipipat = 0
;---------------------------------------------------------------------------------------------------------
;[pm_para] power management
;standby_mode = 0-normal standby, 1-super standby
;---------------------------------------------------------------------------------------------------------
[pm_para]
standby_mode = 1

;*****************************************************************************
;sdram configuration
;
;*****************************************************************************
[dram_para]

dram_clk = 552
dram_type = 3
dram_zq = 0x3bbb
dram_odt_en = 1
dram_para1 = 0x10F20200
dram_para2 = 0x00
dram_mr0 = 0x1840
dram_mr1 = 0x40
dram_mr2 = 0x8
dram_mr3 = 0
dram_tpr0 = 0x0048A192
dram_tpr1 = 0x01B1B18d
dram_tpr2 = 0x00076052
dram_tpr3 = 0x0
dram_tpr4 = 0x0
dram_tpr5 = 0x0
dram_tpr6 = 0x0
dram_tpr7 = 0x0
dram_tpr8 = 0x0
dram_tpr9 = 0x0
dram_tpr10 = 0x0
dram_tpr11 = 0x0
dram_tpr12 = 168
dram_tpr13 = 0x900

;---------------------------------------------------------------------------------------------------------
; if 1 == standby_mode, then support super standby;
; else, support normal standby.
;---------------------------------------------------------------------------------------------------------
[pm_para]
standby_mode = 1

;---------------------------------------------------------------------------------------------------------
; wakeup_src_para:
; sometimes, u would like to add more wakeup src in standby mode, these para will be
; help;
; u need to make sure the standby mode support the wakeup src. Also, some hw
; condition must be guaranteed.
; including:
; cpu_en: power on or off.
; 1: mean power on
; 0: mean power off
; cpu_freq: indicating lowest freq. unit is Mhz;
; dram selfresh_en: selfresh or not.
; 1: enable enter selfresh
; 0: disable enter selfresh
; dram_pll: if not enter selfresh, indicating lowest freq. unit is Mhz;
; wakeup_src: to make the scenario work, the wakeup src is needed.
;---------------------------------------------------------------------------------------------------------
[wakeup_src_para]
cpu_en = 0
cpu_freq = 48
; (cpu:apb:ahb)
pll_ratio = 0x111
dram_selfresh_en = 1
dram_freq = 36
wakeup_src_wl = port:PL07<4><default><default><0>
wakeup_src_bt = port:PL09<4><default><default><0>
;bb_wake_ap = port:PL02<4><default><default><0>

;----------------------------------------------------------------------------------
;i2c configuration
; twi_used = twix enable
;----------------------------------------------------------------------------------
[twi0]
twi_used = 1
twi_scl = port:PH02<2><default><default><default>
twi_sda = port:PH03<2><default><default><default>

[twi1]
twi_used = 1
twi_scl = port:PH04<2><default><default><default>
twi_sda = port:PH05<2><default><default><default>

[twi2]
twi_used = 1
twi_scl = port:PE12<3><default><default><default>
twi_sda = port:PE13<3><default><default><default>


;----------------------------------------------------------------------------------
;uart configuration
;uart_used = uart x enable
;uart_type = 2:2 wire,4:4 wire,8:8 wire, full function
;----------------------------------------------------------------------------------
[uart0]
uart_used = 1
uart_port = 0
uart_type = 2
uart_tx = port:PF02<3><1><default><default>
uart_rx = port:PF04<3><1><default><default>

[uart1]
uart_used = 0
uart_type = 4
uart_tx = port:PG06<2><1><default><default>
uart_rx = port:PG07<2><1><default><default>
uart_rts = port:PG08<2><1><default><default>
uart_cts = port:PG09<2><1><default><default>

[uart2]
uart_used = 0
uart_type = 4
uart_tx = port:PB00<2><1><default><default>
uart_rx = port:PB01<2><1><default><default>
uart_rts = port:PB02<2><1><default><default>
uart_cts = port:PB03<2><1><default><default>

[uart3]
uart_used = 0
uart_type = 4
uart_tx = port:PH06<3><1><default><default>
uart_rx = port:PH07<3><1><default><default>
uart_rts = port:PH08<3><1><default><default>
uart_cts = port:PH09<3><1><default><default>

[uart4]
uart_used = 0
uart_port = 4
uart_type = 2
uart_tx = port:PA04<2><1><default><default>
uart_rx = port:PA05<2><1><default><default>
uart_rts = port:PA06<2><1><default><default>
uart_cts = port:PA07<2><1><default><default>

;----------------------------------------------------------------------------------
;SPI controller configuration
;spi_used = SPIx enable
;spi_cs_bitmap = SPI bit mapping
;----------------------------------------------------------------------------------
[spi0]
spi_used = 0
spi_cs_bitmap = 1
spi_mosi = port:PC00<3><default><default><default>
spi_miso = port:PC01<3><default><default><default>
spi_sclk = port:PC02<3><default><default><default>
spi_cs0 = port:PC03<3><1><default><default>

[spi1]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PA00<2><1><default><default>
spi_sclk = port:PA01<2><default><default><default>
spi_mosi = port:PA02<2><default><default><default>
spi_miso = port:PA03<2><default><default><default>

;----------------------------------------------------------------------------------
;SPI device configuration
;spi_dev_num: number of spi devices
;----------------------------------------------------------------------------------
[spi_devices]
spi_dev_num = 1

;----------------------------------------------------------------------------------
;[spi_board0] spi device configuration
;modalias = spi device name
;max_speed_hz = max transfer speed
;bus_num = bus ID
;chip_select = chip select, 0,1
;mode = SPI transfer mode
;----------------------------------------------------------------------------------
[spi_board0]
modalias = "at25df641"
max_speed_hz = 50000000
bus_num = 0
chip_select = 0
mode = 0

;----------------------------------------------------------------------------------
;capacitor tp configuration
;ctp_twi_id : twi controller ID
;ctp_twi_addr : I2C slave address, 7bit
;ctp_screen_max_x/_y : resolution of touch panel
;ctp_revert_x/_y_flag : whether need to revert x/y
;ctp_exchange_x_y_flag: whether need to exchange the value of x and y
;ctp_int_port : port for tp's interrupt signal
;ctp_wakeup : port for wakeup tp
;----------------------------------------------------------------------------------
[ctp_para]
ctp_used = 1
;ctp_name = "gsl1680e_86dz"
ctp_name = "gsl915_D791C"
ctp_twi_id = 0
ctp_twi_addr = 0x40
ctp_screen_max_x = 768
ctp_screen_max_y = 1024
ctp_revert_x_flag = 0
ctp_revert_y_flag = 0
ctp_exchange_x_y_flag = 0

ctp_cob_gslX680_old = 0
ctp_cob_gslX680 = 999

ctp_int_port = port:PB05<4><default><default><default>
ctp_wakeup = port:PH01<1><default><default><1>
ctp_power_ldo = "axp22_ldoio1"
ctp_power_ldo_vol = 3000
ctp_power_io =

;--------------------------------------------------------------------------------
; CTP automatic detection configuration
;ctp_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[ctp_list_para]
ctp_det_used = 1
ft5x_ts = 0
gt82x = 0
gslX680 = 0
gslX680new = 1
gt9xx_ts = 0
gt9xxf_ts = 1
tu_ts = 0
gt818_ts = 0
zet622x = 0
aw5306_ts = 0
icn83xx_ts = 0
;----------------------------------------------------------------------------------
;touch key configuration
;tkey_twi_id : twi controller ID
;tkey_twi_addr : I2C slave address, 7bit
;tkey_int : port for touch key's interrupt signal
;----------------------------------------------------------------------------------
[tkey_para]
tkey_used = 0
tkey_twi_id =
tkey_twi_addr =
tkey_int =

;----------------------------------------------------------------------------------
;motor configuration
;motor_shake : port for making the moto shaking
;----------------------------------------------------------------------------------
[motor_para]
motor_used = 0
motor_shake = port:power3<1><default><default><1>
motor_ldo = ""
motor_ldo_voltage = 3000

;----------------------------------------------------------------------------------
;thermal configuration
;ths_trip_count : temperature trigger number
;ths_trip_0 : first temperature trigger
;ths_trip_1 : second temperature trigger
;ths_trip_2 : third temperature trigger, when upto this temperature, system shutdown
;ths_trip_0_min : first temperature trigger's min freq
;ths_trip_0_max : first temperature trigger's max freq
;ths_trip_1_min : second temperature trigger's min freq
;ths_trip_1_max : second temperature trigger's max freq
;----------------------------------------------------------------------------------
[ths_para]
ths_used = 1
ths_trip1_count = 3
ths_trip1_0 = 75
ths_trip1_1 = 90
ths_trip1_2 = 110
ths_trip1_0_min = 0
ths_trip1_0_max = 1
ths_trip1_1_min = 1
ths_trip1_1_max = 3
ths_trip1_2_min = 0
ths_trip1_2_max = 0
;----------------------------------------------------------------------------------
;cooler_table cooler_count <=32
;----------------------------------------------------------------------------------
;[cooler_table]
;cooler_count = 4
;cooler0 = "1344000 4 4294967295 0"
;cooler1 = "1200000 4 4294967295 0"
;cooler2 = "1008000 4 4294967295 0"
;cooler3 = "648000 4 4294967295 0"
;
;----------------------------------------------------------------------------------
;[nandx_para]
;nand_support_2ch = support dual channel
;nand0_used = nand0使能标识
;----------------------------------------------------------------------------------
[nand0_para]
nand_support_2ch = 0

nand0_used = 1
nand0_we = port:PC00<2><default><default><default>
nand0_ale = port:PC01<2><default><default><default>
nand0_cle = port:PC02<2><default><default><default>
nand0_ce1 = port:PC03<2><default><default><default>
nand0_ce0 = port:PC04<2><default><default><default>
nand0_nre = port:PC05<2><default><default><default>
nand0_rb0 = port:PC06<2><default><default><default>
nand0_rb1 = port:PC07<2><default><default><default>
nand0_d0 = port:PC08<2><default><default><default>
nand0_d1 = port:PC09<2><default><default><default>
nand0_d2 = port:PC10<2><default><default><default>
nand0_d3 = port:PC11<2><default><default><default>
nand0_d4 = port:PC12<2><default><default><default>
nand0_d5 = port:PC13<2><default><default><default>
nand0_d6 = port:PC14<2><default><default><default>
nand0_d7 = port:PC15<2><default><default><default>
nand0_ndqs = port:PC16<2><default><default><default>
nand0_ce2 = port:PC17<2><default><default><default>
nand0_ce3 = port:PC18<2><default><default><default>

;----------------------------------------------------------------------------------
;disp init configuration
;
;disp_mode (0:screen0<screen0,fb0>)
;screenx_output_type (0:none; 1:lcd; 3:hdmi;)
;screenx_output_mode (used for hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50)
; (5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60)
;fbx format (4:RGB655 5:RGB565 6:RGB556 7:ARGB1555 8:RGBA5551 9:RGB888 10:ARGB8888 12:ARGB4444)
;fbx pixel sequence (0:ARGB 1:BGRA 2:ABGR 3:RGBA)
;fb0_scaler_mode_enable(scaler mode enable, used FE)
;fbx_width,fbx_height (framebuffer horizontal/vertical pixels, fix to output resolution while equal 0)
;lcdx_backlight (lcd init backlight,the range:[0,256],default:197
;lcdx_yy (lcd init screen bright/contrast/saturation/hue, value:0~100, default:50/50/57/50)
;lcd0_contrast (LCD contrast, 0~100)
;lcd0_saturation (LCD saturation, 0~100)
;lcd0_hue (LCD hue, 0~100)
;----------------------------------------------------------------------------------
[disp_init]
disp_init_enable = 1
disp_mode = 0

screen0_output_type = 1
screen0_output_mode = 4

screen1_output_type = 1
screen1_output_mode = 4

fb0_format = 10
fb0_pixel_sequence = 0
fb0_scaler_mode_enable = 0
fb0_width = 0
fb0_height = 0

fb1_format = 10
fb1_pixel_sequence = 0
fb1_scaler_mode_enable = 0
fb1_width = 0
fb1_height = 0

lcd0_backlight = 256
lcd1_backlight = 256

lcd0_bright = 50
lcd0_contrast = 50
lcd0_saturation = 57
lcd0_hue = 50

lcd1_bright = 50
lcd1_contrast = 50
lcd1_saturation = 57
lcd1_hue = 50

;----------------------------------------------------------------------------------
;lcd0 configuration

;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds; 4:dsi; 5:edp; 6:extend dsi
;lcd_x: lcd horizontal resolution
;lcd_y: lcd vertical resolution
;lcd_width: width of lcd in mm
;lcd_height: height of lcd in mm
;lcd_dclk_freq: in MHZ unit
;lcd_pwm_freq: in HZ unit
;lcd_pwm_pol: lcd backlight PWM polarity
;lcd_pwm_max_limit lcd backlight PWM max limit(<=255)
;lcd_hbp: hsync back porch
;lcd_ht: hsync total cycle
;lcd_vbp: vsync back porch
;lcd_vt: vysnc total cycle
;lcd_hspw: hsync plus width
;lcd_vspw: vysnc plus width
;lcd_lvds_if: 0:single link; 1:dual link
;lcd_lvds_colordepth: 0:8bit; 1:6bit
;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode
;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither
;lcd_io_phase: 0:noraml; 1:intert phase(0~3bit: vsync phase; 4~7bit:hsync phase;
; 8~11bit:dclk phase; 12~15bit:de phase)
;lcd_gamma_en lcd gamma correction enable
;lcd_bright_curve_en lcd bright curve correction enable
;lcd_cmap_en lcd color map function enable
;deu_mode 0:smoll lcd screen; 1:large lcd screen(larger than 10inch)
;lcdgamma4iep: Smart Backlight parameter, lcd gamma vale * 10;
; decrease it while lcd is not bright enough; increase while lcd is too bright
;smart_color 90:normal lcd screen 65:retina lcd screen(9.7inch)
;----------------------------------------------------------------------------------
[lcd0_para]
lcd_used = 1

lcd_driver_name = "default_lcd"
lcd_if = 3
lcd_x = 768
lcd_y = 1024
lcd_width = 200
lcd_height = 135
lcd_dclk_freq = 50
lcd_pwm_used = 1
lcd_pwm_ch = 0
lcd_pwm_freq = 50000
lcd_pwm_pol = 0
lcd_hbp = 80
lcd_ht = 928
lcd_hspw = 60
lcd_vbp = 23
lcd_vt = 1065
lcd_vspw = 8
lcd_lvds_if = 0
lcd_lvds_colordepth = 0
lcd_lvds_mode = 0
lcd_frm = 1
lcd_gamma_en = 0
lcd_bright_curve_en = 0
lcd_cmap_en = 0

deu_mode = 0
lcdgamma4iep = 22
smart_color = 90

lcd_bl_en = port:PH06<1><0><default><1>
lcd_power = "axp22_dc1sw"
lcd_gpio_0 = port:PH07<1><0><default><1>
lcd_gpio_1 = port:PL05<1><0><default><1>

lcdd18 = port:PD18<3><0><default><default>
lcdd19 = port:PD19<3><0><default><default>
lcdd20 = port:PD20<3><0><default><default>
lcdd21 = port:PD21<3><0><default><default>
lcdd22 = port:PD22<3><0><default><default>
lcdd23 = port:PD23<3><0><default><default>
lcdclk = port:PD24<3><0><default><default>
lcdde = port:PD25<3><0><default><default>
lcdhsync = port:PD26<3><0><default><default>
lcdvsync = port:PD27<3><0><default><default>


;----------------------------------------------------------------------------------
;pwm config
;----------------------------------------------------------------------------------
[pwm0_para]
pwm_used = 1
pwm_positive = port:PH00<2><0><default><default>

[pwm1_para]
pwm_used = 0
pwm_positive = port:PH01<2><0><default><default>

;--------------------------------------------------------------------------------
;vip (video input port) configuration
;vip_used: 0:disable 1:enable
;vip_mode: 0:sample one interface to one buffer 1:sample two interface to one buffer
;vip_dev_qty: The quantity of devices linked to capture bus
;
;vip_define_sensor_list: If you want use sensor detect function, please set vip_define_sensor_list = 1, and
; verify that file /system/etc/hawkview/sensor_list_cfg.ini is properly configured!
;
;vip_dev(x)_pos: sensor position, "rear" or "front", if vip_define_sensor_list = 1,vip_dev(x)_pos must be configured!
;
;vip_dev(x)_isp_used 0:not use isp 1:use isp
;vip_dev(x)_fmt: 0:yuv 1:bayer raw rgb
;vip_dev(x)_stby_mode: 0:not shut down power at standby 1:shut down power at standby
;vip_dev(x)_vflip: flip in vertical direction 0:disable 1:enable
;vip_dev(x)_hflip: flip in horizontal direction 0:disable 1:enable
;vip_dev(x)_iovdd: camera module io power handle string, pmu power supply
;vip_dev(x)_iovdd_vol: camera module io power voltage, pmu power supply
;vip_dev(x)_avdd: camera module analog power handle string, pmu power supply
;vip_dev(x)_avdd_vol: camera module analog power voltage, pmu power supply
;vip_dev(x)_dvdd: camera module core power handle string, pmu power supply
;vip_dev(x)_dvdd_vol: camera module core power voltage, pmu power supply
;vip_dev(x)_afvdd: camera module vcm power handle string, pmu power supply
;vip_dev(x)_afvdd_vol: camera module vcm power voltage, pmu power supply
;x indicates the index of the devices which are linked to the same capture bus
;fill voltage in uV, e.g. iovdd = 2.8V, vip_devx_iovdd_vol = 2800000
;fill handle string as below:
;axp22_eldo3
;axp22_dldo4
;axp22_eldo2
;fill handle string "" when not using any pmu power supply
;--------------------------------------------------------------------------------

[csi0]

vip_used = 1
;
vip_mode = 0
;
vip_dev_qty = 1
vip_define_sensor_list = 1
vip_csi_pck = port:PE00<2><default><default><default>
vip_csi_mck = port:PE01<2><default><default><default>
vip_csi_hsync = port:PE02<2><default><default><default>
vip_csi_vsync = port:PE03<2><default><default><default>
vip_csi_d0 = port:PE04<2><default><default><default>
vip_csi_d1 = port:PE05<2><default><default><default>
vip_csi_d2 = port:PE06<2><default><default><default>
vip_csi_d3 = port:PE07<2><default><default><default>
vip_csi_d4 = port:PE08<2><default><default><default>
vip_csi_d5 = port:PE09<2><default><default><default>
vip_csi_d6 = port:PE10<2><default><default><default>
vip_csi_d7 = port:PE11<2><default><default><default>

vip_dev0_mname = "gc0308"
vip_dev0_pos = "front"
vip_dev0_lane = 1
vip_dev0_twi_id = 2
vip_dev0_twi_addr = 0x42
vip_dev0_isp_used = 0
vip_dev0_fmt = 0
vip_dev0_stby_mode = 0
vip_dev0_vflip = 0
vip_dev0_hflip = 0
vip_dev0_iovdd = "axp22_dldo3"
vip_dev0_iovdd_vol = 2800000
vip_dev0_avdd = "axp22_ldoio0"
vip_dev0_avdd_vol = 2800000
vip_dev0_dvdd = "axp22_eldo2"
vip_dev0_dvdd_vol = 1800000
vip_dev0_afvdd = ""
vip_dev0_afvdd_vol = 2800000
vip_dev0_power_en =
vip_dev0_reset = port:PE16<1><default><default><0>
vip_dev0_pwdn = port:PE17<1><default><default><1>
vip_dev0_flash_en =
vip_dev0_flash_mode =
vip_dev0_af_pwdn =

vip_dev0_act_used = 0
vip_dev0_act_name = "ad5820_act"
vip_dev0_act_slave = 0x18

vip_dev1_mname = "gc2035"
vip_dev1_pos = "rear"
vip_dev1_lane = 1
vip_dev1_twi_id = 2
vip_dev1_twi_addr = 0x78
vip_dev1_isp_used = 0
vip_dev1_fmt = 0
vip_dev1_stby_mode = 0
vip_dev1_vflip = 0
vip_dev1_hflip = 0
vip_dev1_iovdd = "axp22_dldo3"
vip_dev1_iovdd_vol = 2800000
vip_dev1_avdd = "axp22_ldoio0"
vip_dev1_avdd_vol = 2800000
vip_dev1_dvdd = "axp22_eldo2"
vip_dev1_dvdd_vol = 1800000
vip_dev1_afvdd = ""
vip_dev1_afvdd_vol =
vip_dev1_power_en =
vip_dev1_reset = port:PE16<1><default><default><0>
vip_dev1_pwdn = port:PE17<1><default><default><1>
vip_dev1_flash_en =
vip_dev1_flash_mode =
vip_dev1_af_pwdn =

[camera_list_para]
camera_list_para_used = 1
gc0308 = 1
gc0307 = 1
gt2005 = 1
gc2155 = 0
gc2035 = 1
ov5640 = 1
bf3703 = 0
bf3920 = 0

;-------------------------------------------------------------------------------
; mmc configuration
;
; Config Guide
; sdc_used: 1-enable card, 0-disable card
; sdc_detmode: card detect mode
; 1-detect card by gpio polling
; 2-detect card by gpio irq(must use IO with irq function)
; 3-no detect, always in for boot card
; 4-manually insert and remove by /proc/driver/sunxi-mmc.x/insert
; sdc_buswidth: card bus width, 1-1bit, 4-4bit, 8-8bit
; sdc_use_wp: 1-with write protect IO, 0-no write protect IO
; sdc_isio: for sdio card
; sdc_regulator: power control.if card supports UHS-I/DDR and HS200 timing for
; SD3.0 or eMMC4.5, regulator must be configured. the value is
; the ldo name of AXP221, eg: sdc_regulator = "axp22_eldo2"
; other: GPIO Mapping configuration
;
; Note:
; 1 if detmode=2, sdc_det's config=6
; else if detmode=1, sdc_det's config=0
; else sdc_det IO is not necessary
; 2 if the customer wants to support UHS-I and HS200 features, he must provide
; an independent power supply for the card. This is only used in platforms
; that supports SD3.0 cards and eMMC4.4+ flashes
;-------------------------------------------------------------------------------
[mmc0_para]
sdc_used = 1
sdc_detmode = 2
sdc_buswidth = 4
sdc_d1 = port:PF00<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>
sdc_det = port:PB04<4><1><2><default>
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"

[mmc1_para]
sdc_used = 1
sdc_detmode = 4
sdc_buswidth = 4
sdc_clk = port:PG00<2><1><1><default>
sdc_cmd = port:PG01<2><1><1><default>
sdc_d0 = port:PG02<2><1><1><default>
sdc_d1 = port:PG03<2><1><1><default>
sdc_d2 = port:PG04<2><1><1><default>
sdc_d3 = port:PG05<2><1><1><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 1
sdc_regulator = "none"

[mmc2_para]
sdc_used = 0
sdc_detmode = 3
sdc_buswidth = 8
sdc_2xmode = 1
sdc_clk = port:PC05<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>
sdc_d4 = port:PC12<3><1><2><default>
sdc_d5 = port:PC13<3><1><2><default>
sdc_d6 = port:PC14<3><1><2><default>
sdc_d7 = port:PC15<3><1><2><default>
emmc_rst = port:PC16<3><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"

;----------------------------------------------------------------------------------
;usb configuration
;usb_used: usb controller enable, 0-disable, 1-enable
;usb_port_type: usb mode: 0-device, 1-host, 2-otg
;usb_detect_type: usb hotplug detect mode, 0-none, 1-vbus/id detect, 2-id/dpdm detect
;usb_id_gpio: usb id detect IO
;usb_det_vbus_gpio: usb vbus detect IO, "axp_ctrl" for axp
;usb_drv_vbus_gpio: usb dirve vbus IO
;usb_restrict_gpio: usb current restrict IO
;usb_restric_flag: usb current restrict flag
;----------------------------------------------------------------------------------
[usbc0]
usb_used = 1
usb_port_type = 2
usb_detect_type = 1
usb_id_gpio = port:PH08<0><1><default><default>
usb_det_vbus_gpio = "axp_ctrl"
usb_drv_vbus_gpio = port:power4<1><0><default><0>
usb_restrict_gpio =
usb_host_init_state = 0
usb_restric_flag = 0
usb_restric_voltage = 3550000
usb_restric_capacity = 5
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_regulator_id_vbus = "axp22_dcdc1"
usb_regulator_id_vbus_vol = 3000000

[usbc1]
usb_used = 1
usb_drv_vbus_gpio =
usb_restrict_gpio =
usb_host_init_state = 0
usb_restric_flag = 0
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_not_suspend = 0


;----------------------------------------------------------------------------------

; USB Device vendor Info.
;----------------------------------------------------------------------------------
[usb_feature]
vendor_id = 0x1F3A
mass_storage_id = 0x1000
adb_id = 0x1001

manufacturer_name = "zum"
product_name = "ImPAD0314"
serial_number = "20080411"

[msc_feature]
vendor_name = "zum"
product_name = "ImPAD0314"
release = 100
luns = 2

[serial_feature]
serial_unique = 1

;--------------------------------------------------------------------------------
; G sensor configuration
; gs_twi_id --- TWI ID for controlling Gsensor (0: TWI0, 1: TWI1, 2: TWI2)
;--------------------------------------------------------------------------------
[gsensor_para]
gsensor_used = 1
gsensor_twi_id = 1
gsensor_twi_addr = 0x18
gsensor_int1 = port:PB06<4><1><default><default>
gsensor_int2 =

;--------------------------------------------------------------------------------
; G sensor automatic detection configuration
;gsensor_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[gsensor_list_para]
gsensor_det_used = 1
bma250 = 1
stk831x = 0
mma8452 = 0
mma7660 = 0
mma865x = 0
mc32x0 = 0
afa750 = 0
lis3de_acc = 0
lis3dh_acc = 0
kxtik = 0
dmard10 = 0
dmard06 = 0
mxc622x = 0
fxos8700 = 0
lsm303d = 0

;--------------------------------------------------------------------------------
; gps gpio configuration
; gps_spi_id: the index of SPI controller. 0: SPI0, 1: SPI1, 2: SPI2, 15: no SPI used
; gps_spi_cs_num: the chip select number of SPI controller. 0: SPI CS0, 1: SPI CS1
; gps_lradc: the lradc number for GPS used. 0 and 1 is valid, set 2 if not use lradc
;--------------------------------------------------------------------------------
[gps_para]

;--------------------------------------------------------------------------------
;wifi configuration
;wifi_sdc_id: 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3
;wifi_usbc_id: 0- USB0, 1- USB1, 2- USB2
;wifi_usbc_type: 1- EHCI(speed 2.0), 2- OHCI(speed 1.0)
;wifi_mod_sel: 0- none, 1- ap6181, 2- ap6210(wifi+bt),
; 3 - rtl8188eu, 4- rtl8723au(wifi+bt),
; 5 - rtl8723bs, 6- esp8089
;--------------------------------------------------------------------------------
[wifi_para]
wifi_used = 1
wifi_sdc_id = 1
wifi_usbc_id = 1
wifi_usbc_type = 1
wifi_mod_sel = 8
wifi_power = "axp22_dldo1"
wifi_power_ext1 = "axp22_dldo2"
wifi_power_ext2 = ""
wifi_power_switch = port:power0<1><0><default><0>

; 1 - ap6181 sdio wifi gpio config
;ap6xxx_wl_regon = port:PL06<1><default><default><0>
;ap6xxx_wl_host_wake = port:PL07<4><default><default><0>
;ap6xxx_lpo_use_apclk = 1
; 2 - ap6210 sdio wifi gpio config
;ap6xxx_wl_regon = port:PL06<1><default><default><0>
;ap6xxx_wl_host_wake = port:PL07<4><default><default><0>
;ap6xxx_bt_regon = port:PL08<1><default><default><0>
;ap6xxx_bt_wake = port:PL10<1><default><default><0>
;ap6xxx_bt_host_wake = port:PL09<4><default><default><0>
;ap6xxx_lpo_use_apclk = 1
; 3 - rtl8188eu usb wifi gpio conifg
; 4 - rtl8723au usb wifi + bt
; 5 - rtl8723bs sdio wifi + bt
;rtl8723bs_chip_en = port:PL11<1><default><default><0>
rtl8723bs_wl_regon = port:PL06<1><default><default><0>
rtl8723bs_wl_host_wake = port:PL07<4><default><default><0>
rtl8723bs_bt_regon = port:PL08<1><default><default><0>
rtl8723bs_bt_wake = port:PL10<1><default><default><0>
rtl8723bs_bt_host_wake = port:PL09<4><default><default><0>
rtl8723bs_lpo_use_apclk = 0

rtl8189es_shdn = port:PL06<1><default><default><0>
rtl8189es_host_wake = port:PL07<4><default><default><0>

; 6 - eagle sdio wifi
;esp_wl_chip_en = port:PL03<1><default><default><0>
;esp_wl_rst = port:PL02<1><default><default><0>

;--------------------------------------------------------------------------------
;blue tooth
;bt_used ---- blue tooth used (0- no used, 1- used)
;bt_uard_id ---- uart index
;--------------------------------------------------------------------------------
[bt_para]
bt_used = 0
bt_uart_id = 1

;--------------------------------------------------------------------------------
;3G configuration
;--------------------------------------------------------------------------------
[3g_para]
3g_used = 0
3g_usbc_num = 1
3g_uart_num = 2
bb_name = "em66"
bb_vbat =
bb_on =
bb_pwr_on = port:PL03<1><default><default><0>
bb_wake = port:PL04<1><default><default><0>
bb_rf_dis = port:PL11<1><default><default><0>
bb_rst = port:PL05<1><default><default><0>
bb_dldo = "axp22_aldo1"
bb_dldo_min_uV = 2800000
bb_dldo_max_uV = 2800000

;--------------------------------------------------------------------------------
;gyroscope
;--------------------------------------------------------------------------------
[gy_para]
gy_used = 0
gy_twi_id = 1
gy_twi_addr = 0x6a
gy_int1 =
gy_int2 =

;--------------------------------------------------------------------------------
; Gyro automatic detection configuration
;gy_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[gy_list_para]
gy_det_used = 0
l3gd20_gyr = 1

;--------------------------------------------------------------------------------
;light sensor
;--------------------------------------------------------------------------------
[ls_para]
ls_used = 0
ls_twi_id = 1
ls_twi_addr = 0x23
ls_int = port:PB07<4><1><default><default>

;--------------------------------------------------------------------------------
; lsensor automatic detection configuration
;ls_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[ls_list_para]
ls_det_used = 0
ltr_501als = 1
jsa1212 = 1

;--------------------------------------------------------------------------------
;compass
;--------------------------------------------------------------------------------
[compass_para]
compass_used = 0
compass_twi_id = 1
compass_twi_addr = 0x0d
compass_int =

;--------------------------------------------------------------------------------
;i2s0_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use
; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use
; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use
; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use
;i2s0_select:0 is pcm.1 is i2s
;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use
; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format).
; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format)
; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use
; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge)
;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use
; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM)
; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use
; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM)
;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs
;sample_resolution :16bits/20bits/24bits
;word_select_size :16bits/20bits/24bits/32bits
;pcm_sync_period :16/32/64/128/256
;msb_lsb_first :0: msb first; 1: lsb first
;sign_extend :0: zero pending; 1: sign extend
;slot_index :slot index: 0: the 1st slot - 3: the 4th slot
;slot_width :8 bit width / 16 bit width
;frame_width :0: long frame = 2 clock width; 1: short frame
;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;--------------------------------------------------------------------------------
[i2s0]
i2s0_used = 0
i2s0_channel = 2
i2s0_master = 4
i2s0_select = 1
audio_format = 1
signal_inversion = 1
over_sample_rate = 512
sample_resolution = 16
word_select_size = 32
pcm_sync_period = 256
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 16
frame_width = 1
tx_data_mode = 1
rx_data_mode = 1
i2s0_mclk =
i2s0_bclk = port:PB04<2><1><default><default>
i2s0_lrclk = port:PB05<2><1><default><default>
i2s0_dout0 = port:PB06<2><1><default><default>
i2s0_dout1 =
i2s0_dout2 =
i2s0_dout3 =
i2s0_din = port:PB07<2><1><default><default>

;--------------------------------------------------------------------------------
;i2s1_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use
; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use
; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use
; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use
;i2s1_select:0 is pcm.1 is i2s
;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use
; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format).
; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format)
; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use
; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge)
;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use
; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM)
; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use
; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM)
;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs
;sample_resolution :16bits/20bits/24bits
;word_select_size :16bits/20bits/24bits/32bits
;pcm_sync_period :16/32/64/128/256
;msb_lsb_first :0: msb first; 1: lsb first
;sign_extend :0: zero pending; 1: sign extend
;slot_index :slot index: 0: the 1st slot - 3: the 4th slot
;slot_width :8 bit width / 16 bit width
;frame_width :0: long frame = 2 clock width; 1: short frame
;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;--------------------------------------------------------------------------------
[i2s1]
i2s1_used = 0
i2s1_channel = 2
i2s1_master = 4
i2s1_select = 1
audio_format = 1
signal_inversion = 1
over_sample_rate = 512
sample_resolution = 16
word_select_size = 32
pcm_sync_period = 64
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 16
frame_width = 1
tx_data_mode = 0
rx_data_mode = 0
i2s1_mclk =
i2s1_bclk = port:PG11<2><1><default><default>
i2s1_lrclk = port:PG10<2><1><default><default>
i2s1_dout = port:PG12<2><1><default><default>
i2s1_din = port:PG13<2><1><default><default>

;--------------------------------------------------------------------------------
;pa_single_vol,pa_double_vol: 31 level,1.5db/step.0x1f is the large volume.
;cap_vol:use for system record,0x0--0db,0x1--24db,0x2--27db,0x3--30db,0x4--33db,0x5--36db,0x6--39db,0x7--42db
;headphone_vol,earpiece_vol: must least than 0x3b. 0x1 is a step.
;headset_mic_vol: headset mic(mic2) vol,use for phone headset mic call
;main_mic_vol: main mic(mic1) vol,use for phone main mic call
;--------------------------------------------------------------------------------
[audio0]
audio_used = 1
headphone_vol = 0x3b
earpiece_vol = 0x3b
cap_vol = 0x5
pa_single_vol = 0x3e
pa_double_used = 1
pa_double_vol = 0x3e
headphone_direct_used = 1
headset_mic_vol = 0x6
main_mic_vol = 0x6
audio_hp_ldo = "none"
audio_pa_ctrl = port:PH09<1><default><default><0>
;audio_pa_ctrl = port:PA18<1><default><default><0>
aif2_used = 0
aif3_used = 0
headphone_mute_used = 0
DAC_VOL_CTRL_SPK = 0x9e9e
DAC_VOL_CTRL_HEADPHONE = 0xa0a0
;main_mic_vol = 6

;-------------------------------------------------------------------------------------
;pmu_used ---0:not used,1:used
;pmu_twi_addr ---slave address
;pmu_twi_id ---i2c bus number (0 TWI0, 1 TWI2, 2 TWI3)
;pmu_irq_id ---irq number (0 irq0,1 irq1,……)
;pmu_battery_rdc ---battery initial resistance
;pmu_battery_cap ---battery capability,mAh
;pmu_batdeten ---battery detect en;0:disable 1:enable
;pmu_runtime_chgcur ---set initial charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_earlysuspend_chgcur ---set earlysuspend charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_suspend_chgcur ---set suspend charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_shutdown_chgcur ---set shutdown charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_init_chgvol ---set initial charing target voltage,mV,4100/4220/4200/4240
;pmu_init_chgend_rate ---set initial charing end current rate,10/15
;pmu_init_chg_enabled ---set initial charing enabled,0:disable,1:enable
;pmu_init_adc_freq ---set initial adc frequency,Hz,100/200/400/800
;pmu_init_adcts_freq ---set initial adc TS,Hz,100/200/400/800
;pmu_init_chg_pretime ---set initial pre-charging time,min,40/50/60/70
;pmu_init_chg_csttime ---set initial constance-charging time,min,360/480/600/720
;pmu_batt_cap_correct ---correct the battery capacity or not when one charge cycle 0:not correct 1:correct
;pmu_bat_regu_en ---bat regulator is enable or not when charge done 0:disable 1:enable
;pmu_bat_para1 ---battery indication at 3.13V
;pmu_bat_para2 ---battery indication at 3.27V
;pmu_bat_para3 ---battery indication at 3.34V
;pmu_bat_para4 ---battery indication at 3.41V
;pmu_bat_para5 ---battery indication at 3.48V
;pmu_bat_para6 ---battery indication at 3.52V
;pmu_bat_para7 ---battery indication at 3.55V
;pmu_bat_para8 ---battery indication at 3.57V
;pmu_bat_para9 ---battery indication at 3.59V
;pmu_bat_para10 ---battery indication at 3.61V
;pmu_bat_para11 ---battery indication at 3.63V
;pmu_bat_para12 ---battery indication at 3.64V
;pmu_bat_para13 ---battery indication at 3.66V
;pmu_bat_para14 ---battery indication at 3.7V
;pmu_bat_para15 ---battery indication at 3.73V
;pmu_bat_para16 ---battery indication at 3.77V
;pmu_bat_para17 ---battery indication at 3.78V
;pmu_bat_para18 ---battery indication at 3.8V
;pmu_bat_para19 ---battery indication at 3.82V
;pmu_bat_para20 ---battery indication at 3.84V
;pmu_bat_para21 ---battery indication at 3.85V
;pmu_bat_para22 ---battery indication at 3.87V
;pmu_bat_para23 ---battery indication at 3.91V
;pmu_bat_para24 ---battery indication at 3.94V
;pmu_bat_para25 ---battery indication at 3.98V
;pmu_bat_para26 ---battery indication at 4.01V
;pmu_bat_para27 ---battery indication at 4.05V
;pmu_bat_para28 ---battery indication at 4.08V
;pmu_bat_para29 ---battery indication at 4.1V
;pmu_bat_para30 ---battery indication at 4.12V
;pmu_bat_para31 ---battery indication at 4.14V
;pmu_bat_para32 ---battery indication at 4.15V
;pmu_usbvol_limit ---set usb-ac limited voltage enable,1:enable，0：disable
;pmu_usbcur_limit ---set usb-ac limited current enable,1:enable，0：disable
;pmu_usbvol ---set usb-ac limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite
;pmu_usbcur ---set usb-ac limited current level,mA,500/900, 0 - not limite
;pmu_usbvol_pc ---set usb-pc limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite
;pmu_usbcur_pc ---set usb-pc limited current level,mA,500/900, 0 - not limite
;pmu_pwroff_vol ---set protect voltage when system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pwron_vol ---set protect voltage after system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pekoff_time ---set pek off time,ms, 4000/6000/8000/10000
;pmu_pekoff_func ---set pek off func, 0:shutdown,1:restart
;pmu_pekoff_en ---set pek offlevel powerdown or not, 0:not powerdown,1:powerdown
;pmu_peklong_time ---set pek pek long irq time,ms,1000/1500/2000/2500
;pmu_pekon_time ---set pek on time,ms,128/1000/2000/3000
;pmu_pwrok_time ---set pmu pwrok delay time,ms,8/16/32/64
;pmu_battery_warning_level1 ---low power warning high level,5%-20%,1%/step
;pmu_battery_warning_level2 ---low power warning low level,0%-15%,1%/step
;pmu_restvol_time ---battery indicaton reflash time,30/60/120/
;pmu_ocv_cou_adjust_time ---ocv battery indication reflash time,60/120/30
;pmu_chgled_func ---CHGKED pin control，0:controlled by pmu,1:controlled by Charger
;pmu_chgled_type ---CHGLED Type select when pmu_chgled_func=0,0:Type A，1：Type B
;pmu_vbusen_func ---N_VBUSEN function select,0:as an output,1:as an input
;pmu_reset ---when power key press longer than 16's,PMU reset or not.0:not reset 1:reset
;pmu_IRQ_wakeup ---press IRQ wakeup or not when sleep or power down.0:not wakeup 1:wakeup
;pmu_hot_shutdowm ---when PMU over temperature protect or not;0:disable 1:enable
;pmu_inshort ---ACIN and VBUS inshort or not by software;0:auto detect 1:inshort
;pmu_temp_enable ---temp detect enable
;pmu_charge_ltf ---charge temp low threshold voltage
;pmu_charge_htf ---charge temp high threshold voltage
;pmu_discharge_ltf ---shutdown temp low threshold voltage
;pmu_discharge_htf ---shutdown temp high threshold voltage
;pmu_temp_para1 --- temp -25 voltage
;pmu_temp_para2 --- temp -15 voltage
;pmu_temp_para3 --- temp -10 voltage
;pmu_temp_para4 --- temp -5 voltage
;pmu_temp_para5 --- temp 0 voltage
;pmu_temp_para6 --- temp 5 voltage
;pmu_temp_para7 --- temp 10 voltage
;pmu_temp_para8 --- temp 20 voltage
;pmu_temp_para9 --- temp 30 voltage
;pmu_temp_para10 --- temp 40 voltage
;pmu_temp_para11 --- temp 45 voltage
;pmu_temp_para12 --- temp 50 voltage
;pmu_temp_para13 --- temp 55 voltage
;pmu_temp_para14 --- temp 60 voltage
;pmu_temp_para15 --- temp 70 voltage
;pmu_temp_para16 --- temp 80 voltage
;--------------------------------------------------------------------------------------------------------
[pmu1_para]
pmu_used = 1
pmu_twi_addr = 0x34
pmu_twi_id = 1
pmu_irq_id = 0
pmu_battery_rdc = 162
pmu_battery_cap = 3000
pmu_batdeten = 1
;pmu_chg_ic_temp = 0
pmu_runtime_chgcur = 900
pmu_earlysuspend_chgcur = 900
pmu_suspend_chgcur = 900
pmu_shutdown_chgcur = 900
pmu_init_chgvol = 4200
pmu_init_chgend_rate = 15
pmu_init_chg_enabled = 1
pmu_init_adc_freq = 800
pmu_init_adcts_freq = 800
pmu_init_chg_pretime = 70
pmu_init_chg_csttime = 720
pmu_batt_cap_correct = 1
pmu_bat_regu_en = 1

pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 0
pmu_bat_para5 = 0
pmu_bat_para6 = 0
pmu_bat_para7 = 0
pmu_bat_para8 = 0
pmu_bat_para9 = 1
pmu_bat_para10 = 2
pmu_bat_para11 = 3
pmu_bat_para12 = 5
pmu_bat_para13 = 10
pmu_bat_para14 = 16
pmu_bat_para15 = 31
pmu_bat_para16 = 43
pmu_bat_para17 = 49
pmu_bat_para18 = 53
pmu_bat_para19 = 57
pmu_bat_para20 = 60
pmu_bat_para21 = 63
pmu_bat_para22 = 66
pmu_bat_para23 = 71
pmu_bat_para24 = 77
pmu_bat_para25 = 80
pmu_bat_para26 = 84
pmu_bat_para27 = 88
pmu_bat_para28 = 92
pmu_bat_para29 = 94
pmu_bat_para30 = 96
pmu_bat_para31 = 98
pmu_bat_para32 = 100

pmu_usbvol_limit = 0
pmu_usbcur_limit = 0
pmu_usbvol = 4000
pmu_usbcur = 0
pmu_usbvol_pc = 4400
pmu_usbcur_pc = 500
pmu_pwroff_vol = 3300
pmu_pwron_vol = 2900
pmu_pekoff_time = 8000
pmu_pekoff_func = 0
pmu_pekoff_en = 1
pmu_peklong_time = 1500
pmu_pekon_time = 1000
pmu_pwrok_time = 64
pmu_battery_warning_level1 = 15
pmu_battery_warning_level2 = 0
pmu_restvol_adjust_time = 60
pmu_ocv_cou_adjust_time = 60
pmu_chgled_func = 0
pmu_chgled_type = 0
pmu_vbusen_func = 1
pmu_reset = 0
pmu_IRQ_wakeup = 0
pmu_hot_shutdowm = 1
pmu_inshort = 0
power_start = 0

pmu_temp_enable = 0
pmu_charge_ltf = 2261
pmu_charge_htf = 388
pmu_discharge_ltf = 3200
pmu_discharge_htf = 237
pmu_temp_para1 = 7466
pmu_temp_para2 = 4480
pmu_temp_para3 = 3518
pmu_temp_para4 = 2786
pmu_temp_para5 = 2223
pmu_temp_para6 = 1788
pmu_temp_para7 = 1448
pmu_temp_para8 = 969
pmu_temp_para9 = 664
pmu_temp_para10 = 466
pmu_temp_para11 = 393
pmu_temp_para12 = 333
pmu_temp_para13 = 283
pmu_temp_para14 = 242
pmu_temp_para15 = 179
pmu_temp_para16 = 134

[pmu2_para]
pmu_used = 0
pmu_twi_addr = 0x34
pmu_twi_id = 1
pmu_irq_id = 0
;--------------------------------------------------------------------------------------------------------
[recovery_key]
key_min = 8
key_max = 14
;----------------------------------------------------------------------------------
; dvfs voltage-frequency table configuration
;
; extremity_freq(Hz): cpu extremity frequency when run benckmark or demo apk
; 1536MHz@1500mV with radiator, 1296MHz@1340mV without radiator
; max_freq: cpu maximum frequency, based on Hz, can not be more than 1200MHz
; min_freq: cpu minimum frequency, based on Hz, can not be less than 60MHz
;
; LV_count: count of LV_freq/LV_volt, must be < 16
;
; LV1: core vdd is 1.50v if cpu frequency is (1296Mhz, 1536Mhz]
; LV2: core vdd is 1.34v if cpu frequency is (1200Mhz, 1296Mhz]
; LV3: core vdd is 1.26v if cpu frequency is (1008Mhz, 1200Mhz]
; LV4: core vdd is 1.14v if cpu frequency is (816Mhz, 1008Mhz]
; LV5: core vdd is 1.04v if cpu frequency is (312Mhz, 816Mhz]
; LV6: core vdd is 0.96v if cpu frequency is (0Mhz, 312Mhz]
; LV7: core vdd is 0.96v if cpu frequency is (0Mhz, 312Mhz]
; LV8: core vdd is 0.96v if cpu frequency is (0Mhz, 312Mhz]
;
;----------------------------------------------------------------------------------
[dvfs_table]
extremity_freq = 1344000000
max_freq = 1200000000
min_freq = 60000000

LV_count = 8

LV1_freq = 1536000000
LV1_volt = 1500

LV2_freq = 1344000000
LV2_volt = 1420

LV3_freq = 1200000000
LV3_volt = 1320

LV4_freq = 1008000000
LV4_volt = 1200

LV5_freq = 816000000
LV5_volt = 1100

LV6_freq = 648000000
LV6_volt = 1040

LV7_freq = 0
LV7_volt = 1040

LV8_freq = 0
LV8_volt = 1040

;----------------------------------------------------------------------------------
;virtual device
;virtual device for pinctrl testing
;device have pin PA1 PA2
;----------------------------------------------------------------------------------
[Vdevice]
Vdevice_used = 1
Vdevice_0 = port:PA01<5><1><2><default>
Vdevice_1 = port:PA02<5><1><2><default>

;----------------------------------------------------------------------------------
;s_uart0 config parameters
;s_uart_used --s_uart0 whether used for arisc debugging
;----------------------------------------------------------------------------------
[s_uart0]
s_uart_used = 0
s_uart_tx = port:PL02<2><default><default><default>
s_uart_rx = port:PL03<2><default><default><default>

;----------------------------------------------------------------------------------
;s_rsb0 config parameters
;s_rsb_used --s_rsb0 whether used for arisc
;----------------------------------------------------------------------------------
[s_rsb0]
s_rsb_used = 1
s_rsb_sck = port:PL00<2><1><2><default>
s_rsb_sda = port:PL01<2><1><2><default>

;----------------------------------------------------------------------------------
;s_jtag0 config parameters
;s_jtag0_used --s_jtag0 whether used for arisc
;
;----------------------------------------------------------------------------------
[s_jtag0]
s_jtag_used = 0
s_jtag_tms = port:PL04<2><1><2><default>
s_jtag_tck = port:PL05<2><1><2><default>
s_jtag_tdo = port:PL06<2><1><2><default>
s_jtag_tdi = port:PL07<2><1><2><default>

;----------------------------------------------------------------------------------
;s_powchk cpus power check
;s_powchk_used --power check whether used for arisc in super standby
; bit31:enable power updat, bit1:wakeup when power state exception
; bit0:wakeup when power consumption exception
;s_power_reg the expected regs stand for power on/off state
;s_system_power the limit maxmum power consumption when super standby (unit: mw)
;
;----------------------------------------------------------------------------------
[s_powchk]
s_powchk_used = 0x80000000
s_power_reg = 0x00008061
s_system_power = 50

[mali_para]
mali_used = 1
mali_clkdiv = 1
mali_extreme_freq = 408
mali_extreme_vol = 1100


;----------------------------------------------------------------------------------
; dram dvfs voltage-frequency table configuration
;
; LV_count: count of LV_freq/LV_volt
;
; LV1: core vdd is 1.1v if dram frequency is (360Mhz, 552Mhz]
; LV2: core vdd is 1.0v if dram frequency is ( 0Mhz, 360Mhz]
; LV3: core vdd is 1.0v if dram frequency is ( 0Mhz, 360Mhz]
;
;----------------------------------------------------------------------------------
[dram_dvfs_table]
LV_count = 3

LV1_freq = 432000000
LV1_volt = 1100

LV2_freq = 360000000
LV2_volt = 1000

LV3_freq = 0
LV3_volt = 1000

;----------------------------------------------------------------------------------
;charging_type config parameters
;charging_type 0:uboot charging, 1:android charging
;----------------------------------------------------------------------------------
[charging_type]
charging_type = 1

;----------------------------------------------------------------------------------
;leds config parameters
;leds_used 0:uboot charging, 1:android charging
;----------------------------------------------------------------------------------
;[leds_para]
;leds_used = 0
;red_led = port:power3<1><default><default><0>
;red_led_active_low = 1
;green_led = port:power1<1><default><default><0>
;green_led_active_low = 0
;blue_led =
;blue_led_active_low = 0

[product]
version = "100"
machine = "U7911L3C_PG"

[platform]
eraseflag = 1
next_work = 0

[target]
boot_clock = 1008
storage_type = -1

[key_detect_en]
keyen_flag = 1

[power_sply]
dcdc1_vol = 3000
dcdc2_vol = 1100
dcdc3_vol = 1200
dcdc4_vol = 0
dcdc5_vol = 1500
aldo2_vol = 2500
aldo3_vol = 3000

[card_boot]
logical_start = 40960
sprite_gpio0 =
next_work = 3

[card0_boot_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF00<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>

[card2_boot_para]
card_ctrl = 2
card_high_speed = 1
card_line = 4
sdc_2xmode = 1
sdc_clk = port:PC05<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>

[twi_para]
twi_port = 0
twi_scl = port:PH02<2><default><default><default>
twi_sda = port:PH03<2><default><default><default>

[uart_para]
uart_debug_port = 0
uart_debug_tx = port:PF02<3><1><default><default>
uart_debug_rx = port:PF04<3><1><default><default>

[force_uart_para]
force_uart_port = 0
force_uart_tx = port:PF02<3><1><default><default>
force_uart_rx = port:PF04<3><1><default><default>

[jtag_para]
jtag_enable = 0
jtag_ms = port:PF00<3><default><default><default>
jtag_ck = port:PF05<3><default><default><default>
jtag_do = port:PF03<3><default><default><default>
jtag_di = port:PF01<3><default><default><default>

[clock]
pll3 = 297
pll4 = 300
pll6 = 600
pll8 = 408
pll9 = 480
pll10 = 297
pll_cpupat = 0
pll_gpupat = -1002379674
pll_videopat = 0
pll_vepat = 0
pll_hsicpat = 0
pll_depat = 0
pll_mipipat = 0
pll_mipitun = -1979703288
pll_mipibias = -133168128

[pm_para]
standby_mode = 1

[dram_para]
dram_clk = 552
dram_type = 3
dram_zq = 0x3bbb
dram_odt_en = 1
dram_para1 = 284295680
dram_para2 = 0
dram_mr0 = 6208
dram_mr1 = 64
dram_mr2 = 8
dram_mr3 = 0
dram_tpr0 = 0x48a192
dram_tpr1 = 0x1b1b18d
dram_tpr2 = 0x76052
dram_tpr3 = 0x0
dram_tpr4 = 0x0
dram_tpr5 = 0x0
dram_tpr6 = 0x0
dram_tpr7 = 0x0
dram_tpr8 = 0x0
dram_tpr9 = 0x0
dram_tpr10 = 0x0
dram_tpr11 = 0x0
dram_tpr12 = 0xa8
dram_tpr13 = 0x900

[pm_para]
standby_mode = 1

[wakeup_src_para]
cpu_en = 0
cpu_freq = 48
pll_ratio = 273
dram_selfresh_en = 1
dram_freq = 36
wakeup_src_wl = port:PL07<4><default><default><0>

[twi0]
twi_used = 1
twi_scl = port:PH02<2><default><default><default>
twi_sda = port:PH03<2><default><default><default>

[twi1]
twi_used = 1
twi_scl = port:PH04<2><default><default><default>
twi_sda = port:PH05<2><default><default><default>

[twi2]
twi_used = 1
twi_scl = port:PE12<3><default><default><default>
twi_sda = port:PE13<3><default><default><default>

[uart0]
uart_used = 1
uart_port = 0
uart_type = 2
uart_tx = port:PF02<3><1><default><default>
uart_rx = port:PF04<3><1><default><default>

[uart1]
uart_used = 0
uart_type = 4
uart_tx = port:PG06<2><1><default><default>
uart_rx = port:PG07<2><1><default><default>
uart_rts = port:PG08<2><1><default><default>
uart_cts = port:PG09<2><1><default><default>

[uart2]
uart_used = 0
uart_type = 4
uart_tx = port:PB00<2><1><default><default>
uart_rx = port:PB01<2><1><default><default>
uart_rts = port:PB02<2><1><default><default>
uart_cts = port:PB03<2><1><default><default>

[uart3]
uart_used = 0
uart_type = 4
uart_tx = port:PH06<3><1><default><default>
uart_rx = port:PH07<3><1><default><default>
uart_rts = port:PH08<3><1><default><default>
uart_cts = port:PH09<3><1><default><default>

[uart4]
uart_used = 0
uart_port = 4
uart_type = 2
uart_tx = port:PA04<2><1><default><default>
uart_rx = port:PA05<2><1><default><default>
uart_rts = port:PA06<2><1><default><default>
uart_cts = port:PA07<2><1><default><default>

[spi0]
spi_used = 0
spi_cs_bitmap = 1
spi_mosi = port:PC00<3><default><default><default>
spi_miso = port:PC01<3><default><default><default>
spi_sclk = port:PC02<3><default><default><default>
spi_cs0 = port:PC03<3><1><default><default>

[spi1]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PA00<2><1><default><default>
spi_sclk = port:PA01<2><default><default><default>
spi_mosi = port:PA02<2><default><default><default>
spi_miso = port:PA03<2><default><default><default>

[spi_devices]
spi_dev_num = 0

[spi_board0]
modalias = "at25df641"
max_speed_hz = 50000000
bus_num = 0
chip_select = 0
mode = 0

[ctp_para]
ctp_used = 1
ctp_twi_id = 0
ctp_twi_addr = 0x5d
ctp_screen_max_x = 768
ctp_screen_max_y = 1024
ctp_revert_x_flag = 0
ctp_revert_y_flag = 0
ctp_exchange_x_y_flag = 0
ctp_gslX680_new = 1
ctp_cob_gslX680 = 7911
ctp_cob_gt9xxf = 7912
ctp_int_port = port:PB05<4><default><default><default>
ctp_wakeup = port:PH01<1><default><default><1>
ctp_power_ldo = "axp22_ldoio1"
ctp_power_ldo_vol = 3300
ctp_power_io =

[ctp_list_para]
ctp_det_used = 1
ft5x_ts = 1
gt82x = 1
gslX680 = 0
gslX680new = 1
gt9xx_ts = 0
gt9xxf_ts = 1
tu_ts = 0
gt818_ts = 1
zet622x = 0
aw5306_ts = 0
icn83xx_ts = 0

[tkey_para]
tkey_used = 0
tkey_twi_id =
tkey_twi_addr =
tkey_int =

[motor_para]
motor_used = 0
motor_shake = port:power3<1><default><default><1>
motor_ldo = ""
motor_ldo_voltage = 3300

[ths_para]
ths_used = 1
ths_trip1_count = 3
ths_trip1_0 = 75
ths_trip1_1 = 90
ths_trip1_2 = 110
ths_trip1_0_min = 0
ths_trip1_0_max = 1
ths_trip1_1_min = 1
ths_trip1_1_max = 3
ths_trip1_2_min = 0
ths_trip1_2_max = 0

[cooler_table]
cooler_count = 4
cooler0 = "1344000 4 4294967295 0"
cooler1 = "1200000 4 4294967295 0"
cooler2 = "1008000 4 4294967295 0"
cooler3 = "648000 4 4294967295 0"

[nand0_para]
nand_support_2ch = 0
nand0_used = 1
nand0_we = port:PC00<2><default><default><default>
nand0_ale = port:PC01<2><default><default><default>
nand0_cle = port:PC02<2><default><default><default>
nand0_ce1 = port:PC03<2><default><default><default>
nand0_ce0 = port:PC04<2><default><default><default>
nand0_nre = port:PC05<2><default><default><default>
nand0_rb0 = port:PC06<2><default><default><default>
nand0_rb1 = port:PC07<2><default><default><default>
nand0_d0 = port:PC08<2><default><default><default>
nand0_d1 = port:PC09<2><default><default><default>
nand0_d2 = port:PC10<2><default><default><default>
nand0_d3 = port:PC11<2><default><default><default>
nand0_d4 = port:PC12<2><default><default><default>
nand0_d5 = port:PC13<2><default><default><default>
nand0_d6 = port:PC14<2><default><default><default>
nand0_d7 = port:PC15<2><default><default><default>
nand0_ndqs = port:PC16<2><default><default><default>
nand0_ce2 = port:PC17<2><default><default><default>
nand0_ce3 = port:PC18<2><default><default><default>
id_number_ctl = 2
nand_p1 = 131094

[disp_init]
disp_init_enable = 1
disp_mode = 0
screen0_output_type = 1
screen0_output_mode = 4
screen1_output_type = 1
screen1_output_mode = 4
fb0_format = 10
fb0_pixel_sequence = 0
fb0_scaler_mode_enable = 0
fb0_width = 0
fb0_height = 0
fb1_format = 10
fb1_pixel_sequence = 0
fb1_scaler_mode_enable = 0
fb1_width = 0
fb1_height = 0
lcd0_backlight = 197
lcd1_backlight = 197
lcd0_bright = 50
lcd0_contrast = 50
lcd0_saturation = 57
lcd0_hue = 50
lcd1_bright = 50
lcd1_contrast = 50
lcd1_saturation = 57
lcd1_hue = 50

[lcd0_para]
lcd_used = 1
lcd_driver_name = "default_lcd"
lcd_if = 3
lcd_x = 768
lcd_y = 1024
lcd_width = 120
lcd_height = 160
lcd_dclk_freq = 70
lcd_pwm_used = 1
lcd_pwm_ch = 0
lcd_pwm_freq = 50000
lcd_pwm_pol = 1
lcd_hbp = 80
lcd_ht = 928
lcd_hspw = 10
lcd_vbp = 23
lcd_vt = 1065
lcd_vspw = 10
lcd_lvds_if = 0
lcd_lvds_colordepth = 0
lcd_lvds_mode = 0
lcd_frm = 0
lcd_gamma_en = 0
lcd_bright_curve_en = 0
lcd_cmap_en = 0
deu_mode = 0
lcdgamma4iep = 22
smart_color = 90
lcd_bl_en = port:PH06<1><0><default><1>
lcd_power = port:power2<1><0><default><1>
lcd_gpio_0 = port:PH07<1><0><default><0>
lcdd0 = port:PD18<3><0><default><default>
lcdd1 = port:PD19<3><0><default><default>
lcdd2 = port:PD20<3><0><default><default>
lcdd3 = port:PD21<3><0><default><default>
lcdd4 = port:PD22<3><0><default><default>
lcdd5 = port:PD23<3><0><default><default>
lcdd6 = port:PD24<3><0><default><default>
lcdd7 = port:PD25<3><0><default><default>
lcdd8 = port:PD26<3><0><default><default>
lcdd9 = port:PD27<3><0><default><default>

[pwm0_para]
pwm_used = 1
pwm_positive = port:PH00<2><0><default><default>

[pwm1_para]
pwm_used = 0
pwm_positive = port:PH01<2><0><default><default>

[csi0]
vip_used = 1
vip_mode = 0
vip_dev_qty = 2
vip_define_sensor_list = 0
vip_csi_pck = port:PE00<2><default><default><default>
vip_csi_mck = port:PE01<2><default><default><default>
vip_csi_hsync = port:PE02<2><default><default><default>
vip_csi_vsync = port:PE03<2><default><default><default>
vip_csi_d0 = port:PE04<2><default><default><default>
vip_csi_d1 = port:PE05<2><default><default><default>
vip_csi_d2 = port:PE06<2><default><default><default>
vip_csi_d3 = port:PE07<2><default><default><default>
vip_csi_d4 = port:PE08<2><default><default><default>
vip_csi_d5 = port:PE09<2><default><default><default>
vip_csi_d6 = port:PE10<2><default><default><default>
vip_csi_d7 = port:PE11<2><default><default><default>
vip_dev0_mname = "gc2035"
vip_dev0_pos = "rear"
vip_dev0_lane = 1
vip_dev0_twi_id = 2
vip_dev0_twi_addr = 120
vip_dev0_isp_used = 0
vip_dev0_fmt = 0
vip_dev0_stby_mode = 0
vip_dev0_vflip = 0
vip_dev0_hflip = 0
vip_dev0_iovdd = "axp22_dldo3"
vip_dev0_iovdd_vol = 2800000
vip_dev0_avdd = "axp22_ldoio0"
vip_dev0_avdd_vol = 2800000
vip_dev0_dvdd = "axp22_eldo2"
vip_dev0_dvdd_vol = 1800000
vip_dev0_afvdd = "axp22_eldo3"
vip_dev0_afvdd_vol = 2800000
vip_dev0_power_en =
vip_dev0_reset = port:PE16<1><1><default><0>
vip_dev0_pwdn = port:PE15<1><1><default><1>
vip_dev0_flash_en =
vip_dev0_flash_mode =
vip_dev0_af_pwdn =
vip_dev1_mname = "gc0308"
vip_dev1_pos = "front"
vip_dev1_lane = 1
vip_dev1_twi_id = 2
vip_dev1_twi_addr = 66
vip_dev1_isp_used = 0
vip_dev1_fmt = 0
vip_dev1_stby_mode = 0
vip_dev1_vflip = 0
vip_dev1_hflip = 0
vip_dev1_iovdd = "axp22_dldo3"
vip_dev1_iovdd_vol = 2800000
vip_dev1_avdd = "axp22_ldoio0"
vip_dev1_avdd_vol = 2800000
vip_dev1_dvdd = "axp22_eldo2"
vip_dev1_dvdd_vol = 1800000
vip_dev1_afvdd = "axp22_eldo3"
vip_dev1_afvdd_vol = 2800000
vip_dev1_power_en =
vip_dev1_reset = port:PE16<1><1><default><0>
vip_dev1_pwdn = port:PE17<1><1><default><1>
vip_dev1_flash_en =
vip_dev1_flash_mode =
vip_dev1_af_pwdn =

[camera_list_para]
camera_list_para_used = 1
ov7670 = 0
hi704 = 0
mt9m112 = 0
mt9m113 = 0
ov2655 = 0
hi253 = 0
gc0307 = 0
mt9d112 = 0
ov5647 = 0
gc2015 = 0
ov2643 = 0
tvp5150 = 0
s5k4ec = 0
ov5650_mv9335 = 0
siv120d = 1
siv121d = 1
gc0309 = 1
gc0308 = 1
gc0311 = 1
gc0328 = 1
gc0329 = 1
sp0838 = 1
sp0718 = 1
sp0a19 = 1
bf3a03 = 1
bf3703 = 1
sp2518 = 1
gc2035 = 1
gc2155 = 1
gc2145 = 1
bf3920 = 1
st25a = 1
gt2005 = 1
ov5640 = 1

[mmc0_para]
sdc_used = 1
sdc_detmode = 2
sdc_buswidth = 4
sdc_d1 = port:PF00<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>
sdc_det = port:PB04<4><1><2><default>
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"

[mmc1_para]
sdc_used = 1
sdc_detmode = 4
sdc_buswidth = 4
sdc_clk = port:PG00<2><1><1><default>
sdc_cmd = port:PG01<2><1><1><default>
sdc_d0 = port:PG02<2><1><1><default>
sdc_d1 = port:PG03<2><1><1><default>
sdc_d2 = port:PG04<2><1><1><default>
sdc_d3 = port:PG05<2><1><1><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 1
sdc_regulator = "none"

[mmc2_para]
sdc_used = 0
sdc_detmode = 3
sdc_buswidth = 8
sdc_2xmode = 1
sdc_clk = port:PC05<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>
sdc_d4 = port:PC12<3><1><2><default>
sdc_d5 = port:PC13<3><1><2><default>
sdc_d6 = port:PC14<3><1><2><default>
sdc_d7 = port:PC15<3><1><2><default>
emmc_rst = port:PC16<3><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"

[usbc0]
usb_used = 1
usb_port_type = 2
usb_detect_type = 1
usb_id_gpio = port:PH08<0><1><default><default>
usb_det_vbus_gpio = "axp_ctrl"
usb_drv_vbus_gpio = port:power4<1><0><default><0>
usb_restrict_gpio =
usb_host_init_state = 0
usb_restric_flag = 0
usb_restric_voltage = 3550000
usb_restric_capacity = 5
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_regulator_id_vbus = "axp22_dcdc1"
usb_regulator_id_vbus_vol = 3000000

[usbc1]
usb_used = 0
usb_drv_vbus_gpio =
usb_restrict_gpio =
usb_host_init_state = 0
usb_restric_flag = 0
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_not_suspend = 0

[usb_feature]
vendor_id = 7994
mass_storage_id = 4096
adb_id = 4097
manufacturer_name = "USB Developer"
product_name = "Android"
serial_number = "20080411"

[msc_feature]
vendor_name = "USB 2.0"
product_name = "USB Flash Driver"
release = 100
luns = 2

[serial_feature]
serial_unique = 1

[gsensor_para]
gsensor_used = 1
gsensor_twi_id = 1
gsensor_twi_addr = 0x18
gsensor_int1 =
gsensor_int2 =

[gsensor_list_para]
gsensor_det_used = 1
bma250 = 1
stk831x = 0
mma8452 = 1
mma7660 = 1
mma865x = 1
mc32x0 = 0
afa750 = 1
lis3de_acc = 1
lis3dh_acc = 1
kxtik = 1
dmard10 = 0
dmard06 = 1
mxc622x = 1
fxos8700 = 1
lsm303d = 1

[gps_para]

[wifi_para]
wifi_used = 1
wifi_sdc_id = 1
wifi_usbc_id = 1
wifi_usbc_type = 1
wifi_mod_sel = 8
wifi_power = "axp22_dldo1"
wifi_power_ext1 = "axp22_dldo2"
wifi_power_ext2 = ""
wifi_power_switch = ""
rtl8189es_shdn = port:PL06<1><default><default><0>
rtl8189es_host_wake = port:PL07<4><default><default><1>

[bt_para]
bt_used = 0
bt_uart_id = 1

[3g_para]
3g_used = 0
3g_usbc_num = 1
3g_uart_num = 2
bb_name = "em66"
bb_vbat =
bb_on =
bb_pwr_on = port:PL03<1><default><default><0>
bb_wake = port:PL04<1><default><default><0>
bb_rf_dis = port:PL11<1><default><default><0>
bb_rst = port:PL05<1><default><default><0>
bb_dldo = "axp22_aldo1"
bb_dldo_min_uV = 2800000
bb_dldo_max_uV = 2800000

[gy_para]
gy_used = 0
gy_twi_id = 1
gy_twi_addr = 106
gy_int1 =
gy_int2 =

[gy_list_para]
gy_det_used = 1
l3gd20_gyr = 1

[ls_para]
ls_used = 0
ls_twi_id = 1
ls_twi_addr = 35
ls_int = port:PB07<4><1><default><default>

[ls_list_para]
ls_det_used = 1
ltr_501als = 1
jsa1212 = 1

[compass_para]
compass_used = 0
compass_twi_id = 1
compass_twi_addr = 13
compass_int =

[i2s0]
i2s0_used = 0
i2s0_channel = 2
i2s0_master = 4
i2s0_select = 1
audio_format = 1
signal_inversion = 1
over_sample_rate = 512
sample_resolution = 16
word_select_size = 32
pcm_sync_period = 256
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 16
frame_width = 1
tx_data_mode = 1
rx_data_mode = 1
i2s0_mclk =
i2s0_bclk = port:PB04<2><1><default><default>
i2s0_lrclk = port:PB05<2><1><default><default>
i2s0_dout0 = port:PB06<2><1><default><default>
i2s0_dout1 =
i2s0_dout2 =
i2s0_dout3 =
i2s0_din = port:PB07<2><1><default><default>

[i2s1]
i2s1_used = 0
i2s1_channel = 2
i2s1_master = 4
i2s1_select = 1
audio_format = 1
signal_inversion = 1
over_sample_rate = 512
sample_resolution = 16
word_select_size = 32
pcm_sync_period = 64
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 16
frame_width = 1
tx_data_mode = 0
rx_data_mode = 0
i2s1_mclk =
i2s1_bclk = port:PG11<2><1><default><default>
i2s1_lrclk = port:PG10<2><1><default><default>
i2s1_dout = port:PG12<2><1><default><default>
i2s1_din = port:PG13<2><1><default><default>

[audio0]
audio_used = 1
headphone_vol = 59
earpiece_vol = 59
cap_vol = 5
pa_single_vol = 61
pa_double_used = 1
pa_double_vol = 61
headphone_direct_used = 0
headset_mic_vol = 6
main_mic_vol = 6
audio_hp_ldo = "none"
audio_pa_ctrl = port:PH09<1><default><default><0>
aif2_used = 0
aif3_used = 0
headphone_mute_used = 0
DAC_VOL_CTRL_SPK = 41120
DAC_VOL_CTRL_HEADPHONE = 41120
agc_used = 0
drc_used = 0

[pmu1_para]
pmu_used = 1
pmu_twi_addr = 52
pmu_twi_id = 1
pmu_irq_id = 0
pmu_battery_rdc = 116
pmu_battery_cap = 3540
pmu_batdeten = 1
pmu_chg_ic_temp = 0
pmu_runtime_chgcur = 450
pmu_earlysuspend_chgcur = 1200
pmu_suspend_chgcur = 1500
pmu_shutdown_chgcur = 1500
pmu_init_chgvol = 4200
pmu_init_chgend_rate = 15
pmu_init_chg_enabled = 1
pmu_init_adc_freq = 800
pmu_init_adcts_freq = 800
pmu_init_chg_pretime = 70
pmu_init_chg_csttime = 720
pmu_batt_cap_correct = 1
pmu_bat_regu_en = 0
pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 0
pmu_bat_para5 = 0
pmu_bat_para6 = 0
pmu_bat_para7 = 0
pmu_bat_para8 = 0
pmu_bat_para9 = 1
pmu_bat_para10 = 1
pmu_bat_para11 = 1
pmu_bat_para12 = 2
pmu_bat_para13 = 2
pmu_bat_para14 = 7
pmu_bat_para15 = 13
pmu_bat_para16 = 19
pmu_bat_para17 = 23
pmu_bat_para18 = 27
pmu_bat_para19 = 33
pmu_bat_para20 = 39
pmu_bat_para21 = 44
pmu_bat_para22 = 46
pmu_bat_para23 = 54
pmu_bat_para24 = 60
pmu_bat_para25 = 66
pmu_bat_para26 = 71
pmu_bat_para27 = 76
pmu_bat_para28 = 81
pmu_bat_para29 = 86
pmu_bat_para30 = 90
pmu_bat_para31 = 95
pmu_bat_para32 = 100
pmu_usbvol_limit = 0
pmu_usbcur_limit = 0
pmu_usbvol = 4000
pmu_usbcur = 0
pmu_usbvol_pc = 4400
pmu_usbcur_pc = 500
pmu_pwroff_vol = 3300
pmu_pwron_vol = 2600
pmu_pekoff_time = 6000
pmu_pekoff_func = 0
pmu_pekoff_en = 1
pmu_peklong_time = 1500
pmu_pekon_time = 1000
pmu_pwrok_time = 64
pmu_battery_warning_level1 = 15
pmu_battery_warning_level2 = 0
pmu_restvol_adjust_time = 60
pmu_ocv_cou_adjust_time = 60
pmu_chgled_func = 0
pmu_chgled_type = 0
pmu_vbusen_func = 1
pmu_reset = 0
pmu_IRQ_wakeup = 0
pmu_hot_shutdowm = 1
pmu_inshort = 0
power_start = 0
pmu_temp_enable = 1
pmu_charge_ltf = 2261
pmu_charge_htf = 388
pmu_discharge_ltf = 3200
pmu_discharge_htf = 237
pmu_temp_para1 = 7466
pmu_temp_para2 = 4480
pmu_temp_para3 = 3518
pmu_temp_para4 = 2786
pmu_temp_para5 = 2223
pmu_temp_para6 = 1788
pmu_temp_para7 = 1448
pmu_temp_para8 = 969
pmu_temp_para9 = 664
pmu_temp_para10 = 466
pmu_temp_para11 = 393
pmu_temp_para12 = 333
pmu_temp_para13 = 283
pmu_temp_para14 = 242
pmu_temp_para15 = 179
pmu_temp_para16 = 134

[pmu2_para]
pmu_used = 0
pmu_twi_addr = 52
pmu_twi_id = 1
pmu_irq_id = 0

[recovery_key]
key_min = 2
key_max = 100

[dvfs_table]
extremity_freq = 1344000000
max_freq = 1200000000
min_freq = 120000000
LV_count = 8
LV1_freq = 1536000000
LV1_volt = 1500
LV2_freq = 1344000000
LV2_volt = 1460
LV3_freq = 1200000000
LV3_volt = 1320
LV4_freq = 1008000000
LV4_volt = 1200
LV5_freq = 816000000
LV5_volt = 1100
LV6_freq = 648000000
LV6_volt = 1040
LV7_freq = 0
LV7_volt = 1040
LV8_freq = 0
LV8_volt = 1040

[Vdevice]
Vdevice_used = 1
Vdevice_0 = port:PA01<5><1><2><default>
Vdevice_1 = port:PA02<5><1><2><default>

[s_uart0]
s_uart_used = 0
s_uart_tx = port:PL02<2><default><default><default>
s_uart_rx = port:PL03<2><default><default><default>

[s_rsb0]
s_rsb_used = 1
s_rsb_sck = port:PL00<2><1><2><default>
s_rsb_sda = port:PL01<2><1><2><default>

[s_jtag0]
s_jtag_used = 0
s_jtag_tms = port:PL04<2><1><2><default>
s_jtag_tck = port:PL05<2><1><2><default>
s_jtag_tdo = port:PL06<2><1><2><default>
s_jtag_tdi = port:PL07<2><1><2><default>

[s_powchk]
s_powchk_used = -2147483648
s_power_reg = 32865
s_system_power = 50

[mali_para]
mali_used = 1
mali_clkdiv = 1
mali_extreme_freq = 408
mali_extreme_vol = 1100

[dram_dvfs_table]
LV_count = 3
LV1_freq = 552000000
LV1_volt = 1100
LV2_freq = 360000000
LV2_volt = 1100
LV3_freq = 0
LV3_volt = 1100

[charging_type]
charging_type = 1

[dram_scene_table]
LV_count = 3
LV1_scene = 1
LV1_freq = 360000000
LV2_scene = 2
LV2_freq = 240000000
LV3_scene = 3
LV3_freq = 168000000

adb shell "cat /mnt/sdcard/nandg > /dev/block/nandg; sync"
или с андроида
cat /mnt/sdcard/nandg > /dev/block/nandg; sync

service engsetmacaddr /system/bin/setmacaddr /data/wifimac.txt
class main
oneshot

service setpropserialno /system/bin/sh /system/bin/setserialno.sh
class main
user root
group root
oneshot

on property:ro.inet.wlan.type=8189es
start engsetmacaddr

mkdir /mnt/sdcard/nanda
mount -t vfat /dev/block/nanda /mnt/sdcard/nanda

скопируй скрипт бин в sdcard/nanda с компа и выйди с папки, и вводи следующее

umount /mnt/sdcard/nanda
если не размонтируешь umount /mnt/sdcard/nanda то будет то ли вечный ребут или просто тёмный экран...не помню

adb root
adb remount
adb shell cat /proc/partitions
adb shell "cat /mnt/sdcard/nandb > /dev/block/nandb; sync"
adb shell "cat /mnt/sdcard/nandc > /dev/block/nandc; sync"
adb shell "cat /mnt/sdcard/nandf > /dev/block/nandf; sync"
adb shell "cat /mnt/sdcard/nandg > /dev/block/nandg; sync"
adb shell "cat /mnt/sdcard/nandj > /dev/block/nandj; sync"
adb shell "cat /mnt/sdcard/nandd > /dev/block/nandd; sync"

нажать Ctrl-C для ребута
pause
adb reboot

D:\img\bravis_np_844\NAND BRAVIS\adb nand>adb shell "cat /mnt/sdcard/nandd > /de
v/block/nandd; sync"
Segmentation fault

;A33 Y3 7.85" lcd panel board application
; the difference between Y2 and Y3:
; wifi/bt dram nand
; Y2 AP6210 SKHYNIX MICRON MLC
; Y3 rtl8723bs MIRA TOSHIBA MLC
;---------------------------------------------------------------------------------------------------------
; port configuration:
; port_name = port:GPIO<mux><pull up/down><driver level><default value>
; mux: GPIO function configuration, 0-input, 1-output, 2+: special funciton for modules
; pull up/down: 1-pull up, 2-pull down
; driver level: 0,1,2,3. 2 is recommended
; default value: default output value when this IO is configured as an output IO
;---------------------------------------------------------------------------------------------------------

[product]
version = "100"
machine = "U7911L3C_PG"

;---------------------------------------------------------------------------------------------------------
; eraseflag - 1 erase data partition, 0 - do not erase data partition
; next_work - action after burn, 0x0 by config, 0x1, normal, 0x2 reboot 0x3 ,shutdown,0x4 reupdate ,0x5 boot
;---------------------------------------------------------------------------------------------------------
[platform]
eraseflag = 1
next_work = 0

;----------------------------------------------------------------------------------
;[target] system bootup configuration
;boot_clock = CPU boot frequency, Unit: MHz
;storage_type = boot medium, 0-nand, 1-card0, 2-card2, -1(defualt)auto scan
;----------------------------------------------------------------------------------
[target]
boot_clock = 1008
storage_type = -1

;---------------------------------------------------------------------------------
; uboot key detect enable
; 当keyen_flag = 1 时，支持按键检测
; 当keyen_flag = 0 时，不支持
;---------------------------------------------------------------------------------
[key_detect_en]
keyen_flag = 1

;----------------------------------------------------------------------------------
;dcdc1_vol ---set dcdc1 voltage,mV,1600-3400,100mV/step
;dcdc2_vol ---set dcdc2 voltage,mV,600-1540,20mV/step
;dcdc3_vol ---set dcdc3 voltage,mV,600-1860,20mV/step
;dcdc4_vol ---set dcdc4 voltage,mV,600-1540,20mV/step
;dcdc5_vol ---set dcdc5 voltage,mV,1000-2550,50mV/step
;aldo2_vol ---set aldo2 voltage,mV,700-3300,100mV/step
;aldo3_vol ---set aldo3 voltage,mV,700-3300,100mV/step
;----------------------------------------------------------------------------------
[power_sply]
dcdc1_vol = 3000
dcdc2_vol = 1100
dcdc3_vol = 1200
dcdc4_vol = 0
dcdc5_vol = 1500
aldo2_vol = 2500
aldo3_vol = 3000

;----------------------------------------------------------------------------------
;card boot
;----------------------------------------------------------------------------------
[card_boot]
logical_start = 40960
sprite_gpio0 =
next_work = 3

;----------------------------------------------------------------------------------
;[cardx_boot_para] boot card configuration
;card_ctrl = boot card NO. 0 or 2
;card_high_speed = speed mode, 0-normal mode(up to 25MHz), 1-high speed mode(up to 50MHz)
;card_line = boot card buswidth(1 or 4)
;----------------------------------------------------------------------------------
[card0_boot_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF0<2><1><2><default>
sdc_d0 = port:PF1<2><1><2><default>
sdc_clk = port:PF2<2><1><2><default>
sdc_cmd = port:PF3<2><1><2><default>
sdc_d3 = port:PF4<2><1><2><default>
sdc_d2 = port:PF5<2><1><2><default>

[card2_boot_para]
card_ctrl = 2
card_high_speed = 1
card_line = 4
sdc_2xmode = 1
sdc_clk = port:PC05<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>

;----------------------------------------------------------------------------------
;[twi_para] twi for boot code
;twi_port = twi controller ID
;----------------------------------------------------------------------------------
[twi_para]
twi_port = 0
twi_scl = port:PH02<2><default><default><default>
twi_sda = port:PH03<2><default><default><default>

;----------------------------------------------------------------------------------
;[uart_para] boot debug port configuration
;uart_debug_port = uart port ID for boot debug
;----------------------------------------------------------------------------------
[uart_para]
uart_debug_port = 0
uart_debug_tx = port:PF02<3><1><default><default>
uart_debug_rx = port:PF04<3><1><default><default>

[force_uart_para]
force_uart_port = 0
force_uart_tx = port:PF02<3><1><default><default>
force_uart_rx = port:PF04<3><1><default><default>

;----------------------------------------------------------------------------------
;[jtag_para] jtag configuration
;jtag_enable = 0-disable jtag, 1-enable jtag
;----------------------------------------------------------------------------------
[jtag_para]
jtag_enable = 0
jtag_ms = port:PF00<3><default><default><default>
jtag_ck = port:PF05<3><default><default><default>
jtag_do = port:PF03<3><default><default><default>
jtag_di = port:PF01<3><default><default><default>

;----------------------------------------------------------------------------------
;[clock] pll configuration
;----------------------------------------------------------------------------------
[clock]
pll3 = 297
pll4 = 300
pll6 = 600
pll8 = 408
pll9 = 480
pll10 = 297
pll_cpupat = 0
pll_gpupat = 0xc440e666
pll_videopat = 0
pll_vepat = 0
pll_hsicpat = 0
pll_depat = 0
pll_mipipat = 0
pll_mipitun = 0x8a002008
pll_mipibias= 0xf8100400
;---------------------------------------------------------------------------------------------------------
;[pm_para] power management
;standby_mode = 0-normal standby, 1-super standby
;---------------------------------------------------------------------------------------------------------
[pm_para]
standby_mode = 1

;*****************************************************************************
;sdram configuration
;
;*****************************************************************************
[dram_para]

dram_clk = 552
dram_type = 3
dram_zq = 0x3bbb
dram_odt_en = 1
dram_para1 = 0x10F20200
dram_para2 = 0x00
dram_mr0 = 0x1840
dram_mr1 = 0x40
dram_mr2 = 0x8
dram_mr3 = 0
dram_tpr0 = 0x0048A192
dram_tpr1 = 0x01B1B18d
dram_tpr2 = 0x00076052
dram_tpr3 = 0x0
dram_tpr4 = 0x0
dram_tpr5 = 0x0
dram_tpr6 = 0x0
dram_tpr7 = 0x0
dram_tpr8 = 0x0
dram_tpr9 = 0x0
dram_tpr10 = 0x0
dram_tpr11 = 0x0
dram_tpr12 = 168
dram_tpr13 = 0x10900

;---------------------------------------------------------------------------------------------------------
; if 1 == standby_mode, then support super standby;
; else, support normal standby.
;---------------------------------------------------------------------------------------------------------
[pm_para]
standby_mode = 1

;---------------------------------------------------------------------------------------------------------
; wakeup_src_para:
; sometimes, u would like to add more wakeup src in standby mode, these para will be
; help;
; u need to make sure the standby mode support the wakeup src. Also, some hw
; condition must be guaranteed.
; including:
; cpu_en: power on or off.
; 1: mean power on
; 0: mean power off
; cpu_freq: indicating lowest freq. unit is Mhz;
; dram selfresh_en: selfresh or not.
; 1: enable enter selfresh
; 0: disable enter selfresh
; dram_pll: if not enter selfresh, indicating lowest freq. unit is Mhz;
; wakeup_src: to make the scenario work, the wakeup src is needed.
;---------------------------------------------------------------------------------------------------------
[wakeup_src_para]
cpu_en = 0
cpu_freq = 48
; (cpu:apb:ahb)
pll_ratio = 0x111
dram_selfresh_en = 1
dram_freq = 36
wakeup_src_wl = port:PL07<4><default><default><0>
;wakeup_src_bt = port:PL09<4><default><default><0>
;bb_wake_ap = port:PL02<4><default><default><0>

;----------------------------------------------------------------------------------
;i2c configuration
; twi_used = twix enable
;----------------------------------------------------------------------------------
[twi0]
twi_used = 1
twi_scl = port:PH02<2><default><default><default>
twi_sda = port:PH03<2><default><default><default>

[twi1]
twi_used = 1
twi_scl = port:PH04<2><default><default><default>
twi_sda = port:PH05<2><default><default><default>

[twi2]
twi_used = 1
twi_scl = port:PE12<3><default><default><default>
twi_sda = port:PE13<3><default><default><default>


;----------------------------------------------------------------------------------
;uart configuration
;uart_used = uart x enable
;uart_type = 2:2 wire,4:4 wire,8:8 wire, full function
;----------------------------------------------------------------------------------
[uart0]
uart_used = 1
uart_port = 0
uart_type = 2
uart_tx = port:PF02<3><1><default><default>
uart_rx = port:PF04<3><1><default><default>

[uart1]
uart_used = 0
uart_type = 4
uart_tx = port:PG06<2><1><default><default>
uart_rx = port:PG07<2><1><default><default>
uart_rts = port:PG08<2><1><default><default>
uart_cts = port:PG09<2><1><default><default>

[uart2]
uart_used = 0
uart_type = 4
uart_tx = port:PB00<2><1><default><default>
uart_rx = port:PB01<2><1><default><default>
uart_rts = port:PB02<2><1><default><default>
uart_cts = port:PB03<2><1><default><default>

[uart3]
uart_used = 0
uart_type = 4
uart_tx = port:PH06<3><1><default><default>
uart_rx = port:PH07<3><1><default><default>
uart_rts = port:PH08<3><1><default><default>
uart_cts = port:PH09<3><1><default><default>

[uart4]
uart_used = 0
uart_port = 4
uart_type = 2
uart_tx = port:PA04<2><1><default><default>
uart_rx = port:PA05<2><1><default><default>
uart_rts = port:PA06<2><1><default><default>
uart_cts = port:PA07<2><1><default><default>

;----------------------------------------------------------------------------------
;SPI controller configuration
;spi_used = SPIx enable
;spi_cs_bitmap = SPI bit mapping
;----------------------------------------------------------------------------------
[spi0]
spi_used = 0
spi_cs_bitmap = 1
spi_mosi = port:PC00<3><default><default><default>
spi_miso = port:PC01<3><default><default><default>
spi_sclk = port:PC02<3><default><default><default>
spi_cs0 = port:PC03<3><1><default><default>

[spi1]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PA00<2><1><default><default>
spi_sclk = port:PA01<2><default><default><default>
spi_mosi = port:PA02<2><default><default><default>
spi_miso = port:PA03<2><default><default><default>

;----------------------------------------------------------------------------------
;SPI device configuration
;spi_dev_num: number of spi devices
;----------------------------------------------------------------------------------
[spi_devices]
spi_dev_num = 0

;----------------------------------------------------------------------------------
;[spi_board0] spi device configuration
;modalias = spi device name
;max_speed_hz = max transfer speed
;bus_num = bus ID
;chip_select = chip select, 0,1
;mode = SPI transfer mode
;----------------------------------------------------------------------------------
[spi_board0]
modalias = "at25df641"
max_speed_hz = 50000000
bus_num = 0
chip_select = 0
mode = 0


;----------------------------------------------------------------------------------
;capacitor tp configuration
;ctp_twi_id : twi controller ID
;ctp_twi_addr : I2C slave address, 7bit
;ctp_screen_max_x/_y : resolution of touch panel
;ctp_revert_x/_y_flag : whether need to revert x/y
;ctp_exchange_x_y_flag: whether need to exchange the value of x and y
;ctp_int_port : port for tp's interrupt signal
;ctp_wakeup : port for wakeup tp
;----------------------------------------------------------------------------------
[ctp_para]
ctp_used = 1
ctp_twi_id = 0
ctp_twi_addr = 0x5d
ctp_screen_max_x = 768
ctp_screen_max_y = 1024
ctp_revert_x_flag = 0
ctp_revert_y_flag = 0
ctp_exchange_x_y_flag = 0

ctp_gslX680_new = 1
ctp_cob_gslX680 = 7911
ctp_cob_gt9xxf = 7912

ctp_int_port = port:PB05<4><default><default><default>
ctp_wakeup = port:PH01<1><default><default><1>
ctp_power_ldo = "axp22_ldoio1"
ctp_power_ldo_vol = 3300
ctp_power_io =

;--------------------------------------------------------------------------------
; CTP automatic detection configuration
;ctp_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[ctp_list_para]
ctp_det_used = 1
ft5x_ts = 1
gt82x = 1
gslX680 = 0
gslX680new = 1
gt9xx_ts = 0
gt9xxf_ts = 1
tu_ts = 0
gt818_ts = 1
zet622x = 0
aw5306_ts = 0
icn83xx_ts = 0
;----------------------------------------------------------------------------------
;touch key configuration
;tkey_twi_id : twi controller ID
;tkey_twi_addr : I2C slave address, 7bit
;tkey_int : port for touch key's interrupt signal
;----------------------------------------------------------------------------------
[tkey_para]
tkey_used = 0
tkey_twi_id =
tkey_twi_addr =
tkey_int =

;----------------------------------------------------------------------------------
;motor configuration
;motor_shake : port for making the moto shaking
;----------------------------------------------------------------------------------
[motor_para]
motor_used = 0
motor_shake = port:power3<1><default><default><1>
motor_ldo = ""
motor_ldo_voltage = 3300

;----------------------------------------------------------------------------------
;thermal configuration
;ths_trip_count : temperature trigger number
;ths_trip_0 : first temperature trigger
;ths_trip_1 : second temperature trigger
;ths_trip_2 : third temperature trigger, when upto this temperature, system shutdown
;ths_trip_0_min : first temperature trigger's min freq
;ths_trip_0_max : first temperature trigger's max freq
;ths_trip_1_min : second temperature trigger's min freq
;ths_trip_1_max : second temperature trigger's max freq
;----------------------------------------------------------------------------------
[ths_para]
ths_used = 1
ths_trip1_count = 3
ths_trip1_0 = 75
ths_trip1_1 = 90
ths_trip1_2 = 110
ths_trip1_0_min = 0
ths_trip1_0_max = 1
ths_trip1_1_min = 1
ths_trip1_1_max = 3
ths_trip1_2_min = 0
ths_trip1_2_max = 0
;----------------------------------------------------------------------------------
;cooler_table cooler_count <=32
;----------------------------------------------------------------------------------
[cooler_table]
cooler_count = 4
cooler0 = "1344000 4 4294967295 0"
cooler1 = "1200000 4 4294967295 0"
cooler2 = "1008000 4 4294967295 0"
cooler3 = "648000 4 4294967295 0"

;----------------------------------------------------------------------------------
;[nandx_para]
;nand_support_2ch = support dual channel
;nand0_used = nand0使能标识
;----------------------------------------------------------------------------------
[nand0_para]
nand_support_2ch = 0
id_number_ctl = 0x2
nand_p1 = 0xeeeeee
nand0_used = 1
nand0_we = port:PC00<2><default><2><default>
nand0_ale = port:PC01<2><default><2><default>
nand0_cle = port:PC02<2><default><2><default>
nand0_ce1 = port:PC03<2><default><2><default>
nand0_ce0 = port:PC04<2><default><2><default>
nand0_nre = port:PC05<2><default><2><default>
nand0_rb0 = port:PC06<2><default><2><default>
nand0_rb1 = port:PC07<2><default><2><default>
nand0_d0 = port:PC08<2><default><2><default>
nand0_d1 = port:PC09<2><default><2><default>
nand0_d2 = port:PC10<2><default><2><default>
nand0_d3 = port:PC11<2><default><2><default>
nand0_d4 = port:PC12<2><default><2><default>
nand0_d5 = port:PC13<2><default><2><default>
nand0_d6 = port:PC14<2><default><2><default>
nand0_d7 = port:PC15<2><default><2><default>
nand0_ndqs = port:PC16<2><default><2><default>
nand0_ce2 = port:PC17<2><default><2><default>
nand0_ce3 = port:PC18<2><default><2><default>

;----------------------------------------------------------------------------------
;disp init configuration
;
;disp_mode (0:screen0<screen0,fb0>)
;screenx_output_type (0:none; 1:lcd; 3:hdmi;)
;screenx_output_mode (used for hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50)
; (5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60)
;fbx format (4:RGB655 5:RGB565 6:RGB556 7:ARGB1555 8:RGBA5551 9:RGB888 10:ARGB8888 12:ARGB4444)
;fbx pixel sequence (0:ARGB 1:BGRA 2:ABGR 3:RGBA)
;fb0_scaler_mode_enable(scaler mode enable, used FE)
;fbx_width,fbx_height (framebuffer horizontal/vertical pixels, fix to output resolution while equal 0)
;lcdx_backlight (lcd init backlight,the range:[0,256],default:197
;lcdx_yy (lcd init screen bright/contrast/saturation/hue, value:0~100, default:50/50/57/50)
;lcd0_contrast (LCD contrast, 0~100)
;lcd0_saturation (LCD saturation, 0~100)
;lcd0_hue (LCD hue, 0~100)
;----------------------------------------------------------------------------------
[disp_init]
disp_init_enable = 1
disp_mode = 0

screen0_output_type = 1
screen0_output_mode = 4

screen1_output_type = 1
screen1_output_mode = 4

fb0_format = 10
fb0_pixel_sequence = 0
fb0_scaler_mode_enable = 0
fb0_width = 0
fb0_height = 0

fb1_format = 10
fb1_pixel_sequence = 0
fb1_scaler_mode_enable = 0
fb1_width = 0
fb1_height = 0

lcd0_backlight = 102
lcd1_backlight = 102

lcd0_bright = 50
lcd0_contrast = 50
lcd0_saturation = 57
lcd0_hue = 50

lcd1_bright = 50
lcd1_contrast = 50
lcd1_saturation = 57
lcd1_hue = 50

;----------------------------------------------------------------------------------
;lcd0 configuration

;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds; 4:dsi; 5:edp; 6:extend dsi
;lcd_x: lcd horizontal resolution
;lcd_y: lcd vertical resolution
;lcd_width: width of lcd in mm
;lcd_height: height of lcd in mm
;lcd_dclk_freq: in MHZ unit
;lcd_pwm_freq: in HZ unit
;lcd_pwm_pol: lcd backlight PWM polarity
;lcd_pwm_max_limit lcd backlight PWM max limit(<=255)
;lcd_hbp: hsync back porch
;lcd_ht: hsync total cycle
;lcd_vbp: vsync back porch
;lcd_vt: vysnc total cycle
;lcd_hspw: hsync plus width
;lcd_vspw: vysnc plus width
;lcd_lvds_if: 0:single link; 1:dual link
;lcd_lvds_colordepth: 0:8bit; 1:6bit
;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode
;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither
;lcd_io_phase: 0:noraml; 1:intert phase(0~3bit: vsync phase; 4~7bit:hsync phase;
; 8~11bit:dclk phase; 12~15bit:de phase)
;lcd_gamma_en lcd gamma correction enable
;lcd_bright_curve_en lcd bright curve correction enable
;lcd_cmap_en lcd color map function enable
;deu_mode 0:smoll lcd screen; 1:large lcd screen(larger than 10inch)
;lcdgamma4iep: Smart Backlight parameter, lcd gamma vale * 10;
; decrease it while lcd is not bright enough; increase while lcd is too bright
;smart_color 90:normal lcd screen 65:retina lcd screen(9.7inch)
;----------------------------------------------------------------------------------
[lcd0_para]
lcd_used = 1
lcd_driver_name = "default_lcd"
lcd_if = 3
lcd_x = 768
lcd_y = 1024
lcd_width = 120
lcd_height = 160
lcd_dclk_freq = 50
lcd_pwm_used = 1
lcd_pwm_ch = 0
lcd_pwm_freq = 50000
lcd_pwm_pol = 1
lcd_hbp = 80
lcd_ht = 928
lcd_hspw = 10
lcd_vbp = 23
lcd_vt = 1065
lcd_vspw = 10
lcd_lvds_if = 0
lcd_lvds_colordepth = 0
lcd_lvds_mode = 0
lcd_frm = 0
lcd_gamma_en = 0
lcd_bright_curve_en = 0
lcd_cmap_en = 0

deu_mode = 0
lcdgamma4iep = 22
smart_color = 90

lcd_bl_en = port:PH06<1><0><default><1>
;lcd_power = "axp22_dc1sw"
lcd_power = port:power2<1><0><default><1>
lcd_gpio_0 = port:PH07<1><0><default><0>
;lcd_gpio_1 = port:PL04<1><0><default><1>
;lcd_gpio_2 = port:PL11<1><0><default><0>

lcdd0 = port:PD18<3><0><default><default>
lcdd1 = port:PD19<3><0><default><default>
lcdd2 = port:PD20<3><0><default><default>
lcdd3 = port:PD21<3><0><default><default>
lcdd4 = port:PD22<3><0><default><default>
lcdd5 = port:PD23<3><0><default><default>
lcdd6 = port:PD24<3><0><default><default>
lcdd7 = port:PD25<3><0><default><default>
lcdd8 = port:PD26<3><0><default><default>
lcdd9 = port:PD27<3><0><default><default>

;----------------------------------------------------------------------------------
;pwm config
;----------------------------------------------------------------------------------
[pwm0_para]
pwm_used = 1
pwm_positive = port:PH00<2><0><default><default>

[pwm1_para]
pwm_used = 0
pwm_positive = port:PH01<2><0><default><default>

;--------------------------------------------------------------------------------
;vip (video input port) configuration
;vip_used: 0:disable 1:enable
;vip_mode: 0:sample one interface to one buffer 1:sample two interface to one buffer
;vip_dev_qty: The quantity of devices linked to capture bus
;
;vip_define_sensor_list: If you want use sensor detect function, please set vip_define_sensor_list = 1, and
; verify that file /system/etc/hawkview/sensor_list_cfg.ini is properly configured!
;
;vip_dev(x)_pos: sensor position, "rear" or "front", if vip_define_sensor_list = 1,vip_dev(x)_pos must be configured!
;
;vip_dev(x)_isp_used 0:not use isp 1:use isp
;vip_dev(x)_fmt: 0:yuv 1:bayer raw rgb
;vip_dev(x)_stby_mode: 0:not shut down power at standby 1:shut down power at standby
;vip_dev(x)_vflip: flip in vertical direction 0:disable 1:enable
;vip_dev(x)_hflip: flip in horizontal direction 0:disable 1:enable
;vip_dev(x)_iovdd: camera module io power handle string, pmu power supply
;vip_dev(x)_iovdd_vol: camera module io power voltage, pmu power supply
;vip_dev(x)_avdd: camera module analog power handle string, pmu power supply
;vip_dev(x)_avdd_vol: camera module analog power voltage, pmu power supply
;vip_dev(x)_dvdd: camera module core power handle string, pmu power supply
;vip_dev(x)_dvdd_vol: camera module core power voltage, pmu power supply
;vip_dev(x)_afvdd: camera module vcm power handle string, pmu power supply
;vip_dev(x)_afvdd_vol: camera module vcm power voltage, pmu power supply
;x indicates the index of the devices which are linked to the same capture bus
;fill voltage in uV, e.g. iovdd = 2.8V, vip_devx_iovdd_vol = 2800000
;fill handle string as below:
;axp22_eldo3
;axp22_dldo4
;axp22_eldo2
;fill handle string "" when not using any pmu power supply
;--------------------------------------------------------------------------------

[csi0]

vip_used = 1
vip_mode = 0
vip_dev_qty = 2
vip_define_sensor_list = 0
vip_csi_pck = port:PE00<2><default><default><default>
vip_csi_mck = port:PE01<2><default><default><default>
vip_csi_hsync = port:PE02<2><default><default><default>
vip_csi_vsync = port:PE03<2><default><default><default>
vip_csi_d0 = port:PE04<2><default><default><default>
vip_csi_d1 = port:PE05<2><default><default><default>
vip_csi_d2 = port:PE06<2><default><default><default>
vip_csi_d3 = port:PE07<2><default><default><default>
vip_csi_d4 = port:PE08<2><default><default><default>
vip_csi_d5 = port:PE09<2><default><default><default>
vip_csi_d6 = port:PE10<2><default><default><default>
vip_csi_d7 = port:PE11<2><default><default><default>

vip_dev0_mname = "gc2035"
vip_dev0_pos = "rear"
vip_dev0_lane = 1
vip_dev0_twi_id = 2
vip_dev0_twi_addr = 0x78
vip_dev0_isp_used = 0
vip_dev0_fmt = 0
vip_dev0_stby_mode = 0
vip_dev0_vflip = 0
vip_dev0_hflip = 0
vip_dev0_iovdd = "axp22_dldo3"
vip_dev0_iovdd_vol = 2800000
vip_dev0_avdd = "axp22_ldoio0"
vip_dev0_avdd_vol = 2800000
vip_dev0_dvdd = "axp22_eldo2"
vip_dev0_dvdd_vol = 1800000
vip_dev0_afvdd = ""
vip_dev0_afvdd_vol = 2800000
vip_dev0_power_en =
;vip_dev0_reset = port:PE14<1><default><default><0>
vip_dev0_reset = port:PE16<1><default><default><0>
vip_dev0_pwdn = port:PE15<1><default><default><1>
vip_dev0_flash_en = port:PB00<1><default><default><0>
vip_dev0_flash_mode =
vip_dev0_af_pwdn =


vip_dev1_mname = "gc0308"
vip_dev1_pos = "front"
vip_dev1_lane = 1
vip_dev1_twi_id = 2
vip_dev1_twi_addr = 0x42
vip_dev1_isp_used = 0
vip_dev1_fmt = 0
vip_dev1_stby_mode = 0
vip_dev1_vflip = 0
vip_dev1_hflip = 0
vip_dev1_iovdd = "axp22_dldo3"
vip_dev1_iovdd_vol = 2800000
vip_dev1_avdd = "axp22_ldoio0"
vip_dev1_avdd_vol = 2800000
vip_dev1_dvdd = "axp22_eldo2"
vip_dev1_dvdd_vol = 1800000
vip_dev1_afvdd = ""
vip_dev1_afvdd_vol = 2800000
vip_dev1_power_en =
vip_dev1_reset = port:PE16<1><default><default><0>
vip_dev1_pwdn = port:PE17<1><default><default><1>
;vip_dev1_flash_en = port:PB00<1><default><default><0>
vip_dev1_flash_mode =
vip_dev1_af_pwdn =


;-------------------------------------------------------------------------------
; mmc configuration
;
; Config Guide
; sdc_used: 1-enable card, 0-disable card
; sdc_detmode: card detect mode
; 1-detect card by gpio polling
; 2-detect card by gpio irq(must use IO with irq function)
; 3-no detect, always in for boot card
; 4-manually insert and remove by /proc/driver/sunxi-mmc.x/insert
; sdc_buswidth: card bus width, 1-1bit, 4-4bit, 8-8bit
; sdc_use_wp: 1-with write protect IO, 0-no write protect IO
; sdc_isio: for sdio card
; sdc_regulator: power control.if card supports UHS-I/DDR and HS200 timing for
; SD3.0 or eMMC4.5, regulator must be configured. the value is
; the ldo name of AXP221, eg: sdc_regulator = "axp22_eldo2"
; other: GPIO Mapping configuration
;
; Note:
; 1 if detmode=2, sdc_det's config=6
; else if detmode=1, sdc_det's config=0
; else sdc_det IO is not necessary
; 2 if the customer wants to support UHS-I and HS200 features, he must provide
; an independent power supply for the card. This is only used in platforms
; that supports SD3.0 cards and eMMC4.4+ flashes
;-------------------------------------------------------------------------------
[mmc0_para]
sdc_used = 1
sdc_detmode = 2
sdc_buswidth = 4
sdc_d1 = port:PF00<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d3 = port:PF04<2><0><2><default>
sdc_d2 = port:PF05<2><1><2><default>
;sdc_det = port:PB04<4><1><2><default>
;sdc_power_supply = "axp22_dcdc1"
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"


[mmc1_para]
sdc_used = 1
sdc_detmode = 4
sdc_buswidth = 4
sdc_clk = port:PG00<2><1><1><default>
sdc_cmd = port:PG01<2><1><1><default>
sdc_d0 = port:PG02<2><1><1><default>
sdc_d1 = port:PG03<2><1><1><default>
sdc_d2 = port:PG04<2><1><1><default>
sdc_d3 = port:PG05<2><1><1><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 1
sdc_regulator = "none"

[mmc2_para]
sdc_used = 0
sdc_detmode = 3
sdc_buswidth = 8
sdc_2xmode = 1
sdc_clk = port:PC05<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>
sdc_d4 = port:PC12<3><1><2><default>
sdc_d5 = port:PC13<3><1><2><default>
sdc_d6 = port:PC14<3><1><2><default>
sdc_d7 = port:PC15<3><1><2><default>
emmc_rst = port:PC16<3><1><2><default>
;sdc_power_supply = "axp22_dcdc1"
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"

;----------------------------------------------------------------------------------
;usb configuration
;usb_used: usb controller enable, 0-disable, 1-enable
;usb_port_type: usb mode: 0-device, 1-host, 2-otg
;usb_detect_type: usb hotplug detect mode, 0-none, 1-vbus/id detect, 2-id/dpdm detect
;usb_id_gpio: usb id detect IO
;usb_det_vbus_gpio: usb vbus detect IO, "axp_ctrl" for axp
;usb_drv_vbus_gpio: usb dirve vbus IO
;usb_restrict_gpio: usb current restrict IO
;usb_restric_flag: usb current restrict flag
;----------------------------------------------------------------------------------
[usbc0]
usb_used = 1
usb_port_type = 2
usb_detect_type = 1
usb_id_gpio = port:PH08<0><1><default><default>
usb_det_vbus_gpio = "axp_ctrl"
usb_drv_vbus_gpio = port:power4<1><0><default><0>
usb_restrict_gpio =
usb_host_init_state = 0
usb_restric_flag = 0
usb_restric_voltage = 3550000
usb_restric_capacity= 5
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_regulator_id_vbus = "axp22_dcdc1"
usb_regulator_id_vbus_vol = 3000000

[usbc1]
usb_used = 0
usb_drv_vbus_gpio =
usb_restrict_gpio =
usb_host_init_state = 0
usb_restric_flag = 0
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_not_suspend = 0


;----------------------------------------------------------------------------------

; USB Device vendor Info.
;----------------------------------------------------------------------------------
[usb_feature]
vendor_id = 0x1F3A
mass_storage_id = 0x1000
adb_id = 0x1001

manufacturer_name = "USB Developer"
product_name = "Android"
serial_number = "20080411"

[msc_feature]
vendor_name = "USB 2.0"
product_name = "USB Flash Driver"
release = 100
luns = 2

[serial_feature]
serial_unique = 1

;--------------------------------------------------------------------------------
; G sensor configuration
; gs_twi_id --- TWI ID for controlling Gsensor (0: TWI0, 1: TWI1, 2: TWI2)
;--------------------------------------------------------------------------------
[gsensor_para]
gsensor_used = 1
gsensor_twi_id = 1
gsensor_twi_addr = 0x18
gsensor_int1 =
;port:PB06<4><1><default><default>
gsensor_int2 =

;--------------------------------------------------------------------------------
; G sensor automatic detection configuration
;gsensor_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[gsensor_list_para]
gsensor_det_used = 1
bma250 = 1
stk831x = 0
mma8452 = 1
mma7660 = 1
mma865x = 1
mc32x0 = 0
afa750 = 1
lis3de_acc = 1
lis3dh_acc = 1
kxtik = 1
dmard10 = 0
dmard06 = 1
mxc622x = 1
fxos8700 = 1
lsm303d = 1

;--------------------------------------------------------------------------------
; gps gpio configuration
; gps_spi_id: the index of SPI controller. 0: SPI0, 1: SPI1, 2: SPI2, 15: no SPI used
; gps_spi_cs_num: the chip select number of SPI controller. 0: SPI CS0, 1: SPI CS1
; gps_lradc: the lradc number for GPS used. 0 and 1 is valid, set 2 if not use lradc
;--------------------------------------------------------------------------------
[gps_para]

;--------------------------------------------------------------------------------
;wifi configuration
;wifi_sdc_id: 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3
;wifi_usbc_id: 0- USB0, 1- USB1, 2- USB2
;wifi_usbc_type: 1- EHCI(speed 2.0), 2- OHCI(speed 1.0)
;wifi_mod_sel: 0- none, 1- ap6181, 2- ap6210(wifi+bt),
; 3 - rtl8188eu, 4- rtl8723au(wifi+bt),
; 5 - rtl8723bs, 6- esp8089
;--------------------------------------------------------------------------------
[wifi_para]
wifi_used = 1
wifi_sdc_id = 1
wifi_usbc_id = 1
wifi_usbc_type = 1
wifi_mod_sel = 8
wifi_power = "axp22_dldo1"
wifi_power_ext1 = "axp22_dldo2"
wifi_power_ext2 = ""
wifi_power_switch =
rtl8189es_shdn = port:PL06<1><default><default><0>
rtl8189es_host_wake = port:PL07<4><default><default><1>

;--------------------------------------------------------------------------------
;blue tooth
;bt_used ---- blue tooth used (0- no used, 1- used)
;bt_uard_id ---- uart index
;--------------------------------------------------------------------------------
[bt_para]
bt_used = 0
bt_uart_id = 1

;--------------------------------------------------------------------------------
;3G configuration
;--------------------------------------------------------------------------------
[3g_para]
3g_used = 0
3g_usbc_num = 1
3g_uart_num = 2
bb_name = "em66"
bb_vbat =
bb_on =
bb_pwr_on = port:PL03<1><default><default><0>
bb_wake = port:PL04<1><default><default><0>
bb_rf_dis = port:PL11<1><default><default><0>
bb_rst = port:PL05<1><default><default><0>
bb_dldo = "axp22_aldo1"
bb_dldo_min_uV = 2800000
bb_dldo_max_uV = 2800000

;--------------------------------------------------------------------------------
;gyroscope
;--------------------------------------------------------------------------------
[gy_para]
gy_used = 0
gy_twi_id = 1
gy_twi_addr = 0x6a
gy_int1 =
gy_int2 =

;--------------------------------------------------------------------------------
; Gyro automatic detection configuration
;gy_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[gy_list_para]
gy_det_used = 0
l3gd20_gyr = 1

;--------------------------------------------------------------------------------
;light sensor
;--------------------------------------------------------------------------------
[ls_para]
ls_used = 0
ls_twi_id = 1
ls_twi_addr = 0x23
ls_int = port:PB07<4><1><default><default>

;--------------------------------------------------------------------------------
; lsensor automatic detection configuration
;ls_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[ls_list_para]
ls_det_used = 0
ltr_501als = 1
jsa1212 = 1

;--------------------------------------------------------------------------------
;compass
;--------------------------------------------------------------------------------
[compass_para]
compass_used = 0
compass_twi_id = 1
compass_twi_addr = 0x0d
compass_int =

;--------------------------------------------------------------------------------
;i2s0_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use
; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use
; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use
; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use
;i2s0_select:0 is pcm.1 is i2s
;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use
; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format).
; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format)
; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use
; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge)
;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use
; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM)
; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use
; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM)
;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs
;sample_resolution :16bits/20bits/24bits
;word_select_size :16bits/20bits/24bits/32bits
;pcm_sync_period :16/32/64/128/256
;msb_lsb_first :0: msb first; 1: lsb first
;sign_extend :0: zero pending; 1: sign extend
;slot_index :slot index: 0: the 1st slot - 3: the 4th slot
;slot_width :8 bit width / 16 bit width
;frame_width :0: long frame = 2 clock width; 1: short frame
;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;--------------------------------------------------------------------------------
[i2s0]
i2s0_used = 0
i2s0_channel = 2
i2s0_master = 4
i2s0_select = 1
audio_format = 1
signal_inversion = 1
over_sample_rate = 512
sample_resolution = 16
word_select_size = 32
pcm_sync_period = 256
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 16
frame_width = 1
tx_data_mode = 1
rx_data_mode = 1
i2s0_mclk =
i2s0_bclk = port:PB04<2><1><default><default>
i2s0_lrclk = port:PB05<2><1><default><default>
i2s0_dout0 = port:PB06<2><1><default><default>
i2s0_dout1 =
i2s0_dout2 =
i2s0_dout3 =
i2s0_din = port:PB07<2><1><default><default>

;--------------------------------------------------------------------------------
;i2s1_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use
; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use
; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use
; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use
;i2s1_select:0 is pcm.1 is i2s
;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use
; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format).
; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format)
; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use
; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge)
;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use
; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM)
; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use
; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM)
;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs
;sample_resolution :16bits/20bits/24bits
;word_select_size :16bits/20bits/24bits/32bits
;pcm_sync_period :16/32/64/128/256
;msb_lsb_first :0: msb first; 1: lsb first
;sign_extend :0: zero pending; 1: sign extend
;slot_index :slot index: 0: the 1st slot - 3: the 4th slot
;slot_width :8 bit width / 16 bit width
;frame_width :0: long frame = 2 clock width; 1: short frame
;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;--------------------------------------------------------------------------------
[i2s1]
i2s1_used = 0
i2s1_channel = 2
i2s1_master = 4
i2s1_select = 1
audio_format = 1
signal_inversion = 1
over_sample_rate = 512
sample_resolution = 16
word_select_size = 32
pcm_sync_period = 64
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 16
frame_width = 1
tx_data_mode = 0
rx_data_mode = 0
i2s1_mclk =
i2s1_bclk = port:PG11<2><1><default><default>
i2s1_lrclk = port:PG10<2><1><default><default>
i2s1_dout = port:PG12<2><1><default><default>
i2s1_din = port:PG13<2><1><default><default>

;--------------------------------------------------------------------------------
;pa_single_vol,pa_double_vol,earpiece_vol: 64 level,1db/step.0x3f is the large volume.
;cap_vol:use for system record,0x0--0db,0x1--24db,0x2--27db,0x3--30db,0x4--33db,0x5--36db,0x6--39db,0x7--42db
;headset_mic_vol: headset mic(mic2) vol,use for phone headset mic call
;main_mic_vol: main mic(mic1) vol,use for phone main mic call
;--------------------------------------------------------------------------------
[audio0]
audio_used = 1
audio_hp_ldo = "none"
headphone_vol = 0x3b
earpiece_vol = 0x3e
cap_vol = 0x6
pa_single_vol = 0x3e
pa_double_used = 1
pa_double_vol = 0x3e
headphone_direct_used = 1
headset_mic_vol = 3
main_mic_vol = 1
audio_pa_ctrl = port:PH09<1><default><default><0>
aif2_used = 0
aif3_used = 0
headphone_mute_used = 0
DAC_VOL_CTRL_SPK = 0xa0a0
DAC_VOL_CTRL_HEADPHONE = 0xa0a0
agc_used = 0
drc_used = 0
;-------------------------------------------------------------------------------------
;pmu_used ---0:not used,1:used
;pmu_twi_addr ---slave address
;pmu_twi_id ---i2c bus number (0 TWI0, 1 TWI2, 2 TWI3)
;pmu_irq_id ---irq number (0 irq0,1 irq1,……)
;pmu_battery_rdc ---battery initial resistance
;pmu_battery_cap ---battery capability,mAh
;pmu_batdeten ---battery detect en;0:disable 1:enable
;PMU_CHG_IC_temp used for battery temperature protect when charging
;PMU_CHG_IC_temp --the object temperature want to adjust to (unit: 'C'), 0: this function unused, other value is object temperature
;pmu_runtime_chgcur ---set initial charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_earlysuspend_chgcur ---set earlysuspend charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_suspend_chgcur ---set suspend charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_shutdown_chgcur ---set shutdown charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_init_chgvol ---set initial charing target voltage,mV,4100/4220/4200/4240
;pmu_init_chgend_rate ---set initial charing end current rate,10/15
;pmu_init_chg_enabled ---set initial charing enabled,0:disable,1:enable
;pmu_init_adc_freq ---set initial adc frequency,Hz,100/200/400/800
;pmu_init_adcts_freq ---set initial adc TS,Hz,100/200/400/800
;pmu_init_chg_pretime ---set initial pre-charging time,min,40/50/60/70
;pmu_init_chg_csttime ---set initial constance-charging time,min,360/480/600/720
;pmu_batt_cap_correct ---correct the battery capacity or not when one charge cycle 0:not correct 1:correct
;pmu_bat_regu_en ---bat regulator is enable or not when charge done 0:disable 1:enable
;pmu_bat_para1 ---battery indication at 3.13V
;pmu_bat_para2 ---battery indication at 3.27V
;pmu_bat_para3 ---battery indication at 3.34V
;pmu_bat_para4 ---battery indication at 3.41V
;pmu_bat_para5 ---battery indication at 3.48V
;pmu_bat_para6 ---battery indication at 3.52V
;pmu_bat_para7 ---battery indication at 3.55V
;pmu_bat_para8 ---battery indication at 3.57V
;pmu_bat_para9 ---battery indication at 3.59V
;pmu_bat_para10 ---battery indication at 3.61V
;pmu_bat_para11 ---battery indication at 3.63V
;pmu_bat_para12 ---battery indication at 3.64V
;pmu_bat_para13 ---battery indication at 3.66V
;pmu_bat_para14 ---battery indication at 3.7V
;pmu_bat_para15 ---battery indication at 3.73V
;pmu_bat_para16 ---battery indication at 3.77V
;pmu_bat_para17 ---battery indication at 3.78V
;pmu_bat_para18 ---battery indication at 3.8V
;pmu_bat_para19 ---battery indication at 3.82V
;pmu_bat_para20 ---battery indication at 3.84V
;pmu_bat_para21 ---battery indication at 3.85V
;pmu_bat_para22 ---battery indication at 3.87V
;pmu_bat_para23 ---battery indication at 3.91V
;pmu_bat_para24 ---battery indication at 3.94V
;pmu_bat_para25 ---battery indication at 3.98V
;pmu_bat_para26 ---battery indication at 4.01V
;pmu_bat_para27 ---battery indication at 4.05V
;pmu_bat_para28 ---battery indication at 4.08V
;pmu_bat_para29 ---battery indication at 4.1V
;pmu_bat_para30 ---battery indication at 4.12V
;pmu_bat_para31 ---battery indication at 4.14V
;pmu_bat_para32 ---battery indication at 4.15V
;pmu_usbvol_limit ---set usb-ac limited voltage enable,1:enable，0：disable
;pmu_usbcur_limit ---set usb-ac limited current enable,1:enable，0：disable
;pmu_usbvol ---set usb-ac limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite
;pmu_usbcur ---set usb-ac limited current level,mA,500/900, 0 - not limite
;pmu_usbvol_pc ---set usb-pc limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite
;pmu_usbcur_pc ---set usb-pc limited current level,mA,500/900, 0 - not limite
;pmu_pwroff_vol ---set protect voltage when system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pwron_vol ---set protect voltage after system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pekoff_time ---set pek off time,ms, 4000/6000/8000/10000
;pmu_pekoff_func ---set pek off func, 0:shutdown,1:restart
;pmu_pekoff_en ---set pek offlevel powerdown or not, 0:not powerdown,1:powerdown
;pmu_peklong_time ---set pek pek long irq time,ms,1000/1500/2000/2500
;pmu_pekon_time ---set pek on time,ms,128/1000/2000/3000
;pmu_pwrok_time ---set pmu pwrok delay time,ms,8/16/32/64
;pmu_battery_warning_level1 ---low power warning high level,5%-20%,1%/step
;pmu_battery_warning_level2 ---low power warning low level,0%-15%,1%/step
;pmu_restvol_time ---battery indicaton reflash time,30/60/120/
;pmu_ocv_cou_adjust_time ---ocv battery indication reflash time,60/120/30
;pmu_chgled_func ---CHGKED pin control，0:controlled by pmu,1:controlled by Charger
;pmu_chgled_type ---CHGLED Type select when pmu_chgled_func=0,0:Type A，1：Type B
;pmu_vbusen_func ---N_VBUSEN function select,0:as an output,1:as an input
;pmu_reset ---when power key press longer than 16's,PMU reset or not.0:not reset 1:reset
;pmu_IRQ_wakeup ---press IRQ wakeup or not when sleep or power down.0:not wakeup 1:wakeup
;pmu_hot_shutdowm ---when PMU over temperature protect or not;0:disable 1:enable
;pmu_inshort ---ACIN and VBUS inshort or not by software;0:auto detect 1:inshort
;pmu_temp_enable ---temp detect enable
;pmu_charge_ltf ---charge temp low threshold voltage
;pmu_charge_htf ---charge temp high threshold voltage
;pmu_discharge_ltf ---shutdown temp low threshold voltage
;pmu_discharge_htf ---shutdown temp high threshold voltage
;pmu_temp_para1 --- temp -25 voltage
;pmu_temp_para2 --- temp -15 voltage
;pmu_temp_para3 --- temp -10 voltage
;pmu_temp_para4 --- temp -5 voltage
;pmu_temp_para5 --- temp 0 voltage
;pmu_temp_para6 --- temp 5 voltage
;pmu_temp_para7 --- temp 10 voltage
;pmu_temp_para8 --- temp 20 voltage
;pmu_temp_para9 --- temp 30 voltage
;pmu_temp_para10 --- temp 40 voltage
;pmu_temp_para11 --- temp 45 voltage
;pmu_temp_para12 --- temp 50 voltage
;pmu_temp_para13 --- temp 55 voltage
;pmu_temp_para14 --- temp 60 voltage
;pmu_temp_para15 --- temp 70 voltage
;pmu_temp_para16 --- temp 80 voltage
;--------------------------------------------------------------------------------------------------------
[pmu1_para]
pmu_used = 1
pmu_twi_addr = 0x34
pmu_twi_id = 1
pmu_irq_id = 0
pmu_battery_rdc = 116
pmu_battery_cap = 3540
pmu_batdeten = 1
pmu_chg_ic_temp = 0
pmu_runtime_chgcur = 450
pmu_earlysuspend_chgcur = 1200
pmu_suspend_chgcur = 1500
pmu_shutdown_chgcur = 1500
pmu_init_chgvol = 4200
pmu_init_chgend_rate = 15
pmu_init_chg_enabled = 1
pmu_init_adc_freq = 800
pmu_init_adcts_freq = 800
pmu_init_chg_pretime = 70
pmu_init_chg_csttime = 720
pmu_batt_cap_correct = 1
pmu_bat_regu_en = 0

pmu_bat_regu_en = 0
pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 0
pmu_bat_para5 = 0
pmu_bat_para6 = 0
pmu_bat_para7 = 0
pmu_bat_para8 = 0
pmu_bat_para9 = 1
pmu_bat_para10 = 1
pmu_bat_para11 = 1
pmu_bat_para12 = 2
pmu_bat_para13 = 2
pmu_bat_para14 = 7
pmu_bat_para15 = 13
pmu_bat_para16 = 19
pmu_bat_para17 = 23
pmu_bat_para18 = 27
pmu_bat_para19 = 33
pmu_bat_para20 = 39
pmu_bat_para21 = 44
pmu_bat_para22 = 46
pmu_bat_para23 = 54
pmu_bat_para24 = 60
pmu_bat_para25 = 66
pmu_bat_para26 = 71
pmu_bat_para27 = 76
pmu_bat_para28 = 81
pmu_bat_para29 = 86
pmu_bat_para30 = 90
pmu_bat_para31 = 95
pmu_bat_para32 = 100

pmu_usbvol_limit = 0
pmu_usbcur_limit = 0
pmu_usbvol = 4000
pmu_usbcur = 0
pmu_usbvol_pc = 4400
pmu_usbcur_pc = 500
pmu_pwroff_vol = 3300
pmu_pwron_vol = 2600
pmu_pekoff_time = 6000
pmu_pekoff_func = 0
pmu_pekoff_en = 1
pmu_peklong_time = 1500
pmu_pekon_time = 1000
pmu_pwrok_time = 64
pmu_battery_warning_level1 = 15
pmu_battery_warning_level2 = 0
pmu_restvol_adjust_time = 60
pmu_ocv_cou_adjust_time = 60
pmu_chgled_func = 0
pmu_chgled_type = 0
pmu_vbusen_func = 1
pmu_reset = 0
pmu_IRQ_wakeup = 0
pmu_hot_shutdowm = 1
pmu_inshort = 0
power_start = 0

pmu_temp_enable = 1
pmu_charge_ltf = 2261
pmu_charge_htf = 388
pmu_discharge_ltf = 3200
pmu_discharge_htf = 237
pmu_temp_para1 = 7466
pmu_temp_para2 = 4480
pmu_temp_para3 = 3518
pmu_temp_para4 = 2786
pmu_temp_para5 = 2223
pmu_temp_para6 = 1788
pmu_temp_para7 = 1448
pmu_temp_para8 = 969
pmu_temp_para9 = 664
pmu_temp_para10 = 466
pmu_temp_para11 = 393
pmu_temp_para12 = 333
pmu_temp_para13 = 283
pmu_temp_para14 = 242
pmu_temp_para15 = 179
pmu_temp_para16 = 134

[pmu2_para]
pmu_used = 0
pmu_twi_addr = 0x34
pmu_twi_id = 1
pmu_irq_id = 0

;--------------------------------------------------------------------------------------------------------
[recovery_key]
key_min = 2
key_max = 100

;----------------------------------------------------------------------------------
; dvfs voltage-frequency table configuration
;
; extremity_freq(Hz): cpu extremity frequency when run benckmark or demo apk
; 1344MHz@1460mV with radiator
; max_freq: cpu maximum frequency, based on Hz, can not be more than 1344MHz
; min_freq: cpu minimum frequency, based on Hz, can not be less than 120MHz
;
; LV_count: count of LV_freq/LV_volt, must be < 16
;
; LV1: core vdd is 1.50v if cpu frequency is (1344Mhz, 1536Mhz]
; LV2: core vdd is 1.46v if cpu frequency is (1200Mhz, 1344Mhz]
; LV3: core vdd is 1.32v if cpu frequency is (1008Mhz, 1200Mhz]
; LV4: core vdd is 1.20v if cpu frequency is (816Mhz, 1008Mhz]
; LV5: core vdd is 1.10v if cpu frequency is (648Mhz, 816Mhz]
; LV6: core vdd is 1.04v if cpu frequency is (120Mhz, 648Mhz]
; LV7: core vdd is 1.04v if cpu frequency is (120Mhz, 648Mhz]
; LV8: core vdd is 1.04v if cpu frequency is (120Mhz, 648Mhz]
;
;----------------------------------------------------------------------------------
[dvfs_table]
extremity_freq = 1344000000
max_freq = 1200000000
min_freq = 60000000

LV_count = 8

LV1_freq = 1536000000
LV1_volt = 1500

LV2_freq = 1344000000
LV2_volt = 1460

LV3_freq = 1200000000
LV3_volt = 1320

LV4_freq = 1008000000
LV4_volt = 1200

LV5_freq = 816000000
LV5_volt = 1100

LV6_freq = 648000000
LV6_volt = 1040

LV7_freq = 0
LV7_volt = 1040

LV8_freq = 0
LV8_volt = 1040

;----------------------------------------------------------------------------------
;virtual device
;virtual device for pinctrl testing
;device have pin PA1 PA2
;----------------------------------------------------------------------------------
[Vdevice]
Vdevice_used = 1
Vdevice_0 = port:PA01<5><1><2><default>
Vdevice_1 = port:PA02<5><1><2><default>

;----------------------------------------------------------------------------------
;s_uart0 config parameters
;s_uart_used --s_uart0 whether used for arisc debugging
;----------------------------------------------------------------------------------
[s_uart0]
s_uart_used = 0
s_uart_tx = port:PL02<2><default><default><default>
s_uart_rx = port:PL03<2><default><default><default>

;----------------------------------------------------------------------------------
;s_rsb0 config parameters
;s_rsb_used --s_rsb0 whether used for arisc
;----------------------------------------------------------------------------------
[s_rsb0]
s_rsb_used = 1
s_rsb_sck = port:PL00<2><1><2><default>
s_rsb_sda = port:PL01<2><1><2><default>

;----------------------------------------------------------------------------------
;s_jtag0 config parameters
;s_jtag0_used --s_jtag0 whether used for arisc
;
;----------------------------------------------------------------------------------
[s_jtag0]
s_jtag_used = 0
s_jtag_tms = port:PL04<2><1><2><default>
s_jtag_tck = port:PL05<2><1><2><default>
s_jtag_tdo = port:PL06<2><1><2><default>
s_jtag_tdi = port:PL07<2><1><2><default>

;----------------------------------------------------------------------------------
;s_powchk cpus power check
;s_powchk_used --power check whether used for arisc in super standby
; bit31:enable power updat, bit1:wakeup when power state exception
; bit0:wakeup when power consumption exception
;s_power_reg the expected regs stand for power on/off state
;s_system_power the limit maxmum power consumption when super standby (unit: mw)
;
;----------------------------------------------------------------------------------
[s_powchk]
s_powchk_used = 0x80000000
s_power_reg = 0x00008061
s_system_power = 50

[mali_para]
mali_used = 1
mali_clkdiv = 1
mali_extreme_freq = 408
mali_extreme_vol = 1100


;----------------------------------------------------------------------------------
; dram dvfs voltage-frequency table configuration
;
; LV_count: count of LV_freq/LV_volt
;
; LV1: core vdd is 1.1v if dram frequency is (360Mhz, 552Mhz]
; LV2: core vdd is 1.0v if dram frequency is ( 0Mhz, 360Mhz]
; LV3: core vdd is 1.0v if dram frequency is ( 0Mhz, 360Mhz]
;
;----------------------------------------------------------------------------------
[dram_dvfs_table]
LV_count = 3

LV1_freq = 552000000
LV1_volt = 1100

LV2_freq = 360000000
LV2_volt = 1100

LV3_freq = 0
LV3_volt = 1100

;----------------------------------------------------------------------------------
;charging_type config parameters
;charging_type 0:uboot charging, 1:android charging
;----------------------------------------------------------------------------------
[charging_type]
charging_type = 1


;----------------------------------------------------------------------------------
; dram scene frequency table configuration
;
; LV_count: count of LV_scene/LV_freq
;
; LV1: dram frequency default is 360MHz in home, supported for 360MHz/552MHz
; LV2: dram frequency default is 240MHz in video play, supported for 240MHz/360MHz/552MHz
; LV3: dram frequency default is 168MHz in bgmusic play
;
;----------------------------------------------------------------------------------
[dram_scene_table]
LV_count = 3

LV1_scene = 1
LV1_freq = 360000000

LV2_scene = 2
LV2_freq = 240000000

LV3_scene = 3
LV3_freq = 168000000

;----------------------------------------------------------------------------------
;leds config parameters
;leds_used 0:uboot charging, 1:android charging
;----------------------------------------------------------------------------------
;[leds_para]
;leds_used = 1
;red_led = port:power3<1><default><default><0>
;red_led_active_low = 1
;green_led = port:power1<1><default><default><0>
;green_led_active_low = 0
;blue_led =
;blue_led_active_low = 0

[product]
version = "100"
machine = "U7911L3C_PG"

[platform]
eraseflag = 1
next_work = 0

[target]
boot_clock = 1008
storage_type = -1

[key_detect_en]
keyen_flag = 1

[power_sply]
dcdc1_vol = 3000
dcdc2_vol = 1100
dcdc3_vol = 1200
dcdc4_vol = 0
dcdc5_vol = 1500
aldo2_vol = 2500
aldo3_vol = 3000

[card_boot]
logical_start = 40960
sprite_gpio0 =
next_work = 3

[card0_boot_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF00<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>

[card2_boot_para]
card_ctrl = 2
card_high_speed = 1
card_line = 4
sdc_2xmode = 1
sdc_clk = port:PC05<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>

[twi_para]
twi_port = 0
twi_scl = port:PH02<2><default><default><default>
twi_sda = port:PH03<2><default><default><default>

[uart_para]
uart_debug_port = 0
uart_debug_tx = port:PF02<3><1><default><default>
uart_debug_rx = port:PF04<3><1><default><default>

[force_uart_para]
force_uart_port = 0
force_uart_tx = port:PF02<3><1><default><default>
force_uart_rx = port:PF04<3><1><default><default>

[jtag_para]
jtag_enable = 0
jtag_ms = port:PF00<3><default><default><default>
jtag_ck = port:PF05<3><default><default><default>
jtag_do = port:PF03<3><default><default><default>
jtag_di = port:PF01<3><default><default><default>

[clock]
pll3 = 297
pll4 = 300
pll6 = 600
pll8 = 408
pll9 = 480
pll10 = 297
pll_cpupat = 0
pll_gpupat = -1002379674
pll_videopat = 0
pll_vepat = 0
pll_hsicpat = 0
pll_depat = 0
pll_mipipat = 0
pll_mipitun = -1979703288
pll_mipibias = -133168128

[pm_para]
standby_mode = 1

[dram_para]
dram_clk = 552
dram_type = 3
dram_zq = 0x3bbb
dram_odt_en = 1
dram_para1 = 284295680
dram_para2 = 0
dram_mr0 = 6208
dram_mr1 = 64
dram_mr2 = 8
dram_mr3 = 0
dram_tpr0 = 0x48a192
dram_tpr1 = 0x1b1b18d
dram_tpr2 = 0x76052
dram_tpr3 = 0x0
dram_tpr4 = 0x0
dram_tpr5 = 0x0
dram_tpr6 = 0x0
dram_tpr7 = 0x0
dram_tpr8 = 0x0
dram_tpr9 = 0x0
dram_tpr10 = 0x0
dram_tpr11 = 0x0
dram_tpr12 = 0xa8
dram_tpr13 = 0x900

[pm_para]
standby_mode = 1

[wakeup_src_para]
cpu_en = 0
cpu_freq = 48
pll_ratio = 273
dram_selfresh_en = 1
dram_freq = 36
wakeup_src_wl = port:PL07<4><default><default><0>

[twi0]
twi_used = 1
twi_scl = port:PH02<2><default><default><default>
twi_sda = port:PH03<2><default><default><default>

[twi1]
twi_used = 1
twi_scl = port:PH04<2><default><default><default>
twi_sda = port:PH05<2><default><default><default>

[twi2]
twi_used = 1
twi_scl = port:PE12<3><default><default><default>
twi_sda = port:PE13<3><default><default><default>

[uart0]
uart_used = 1
uart_port = 0
uart_type = 2
uart_tx = port:PF02<3><1><default><default>
uart_rx = port:PF04<3><1><default><default>

[uart1]
uart_used = 0
uart_type = 4
uart_tx = port:PG06<2><1><default><default>
uart_rx = port:PG07<2><1><default><default>
uart_rts = port:PG08<2><1><default><default>
uart_cts = port:PG09<2><1><default><default>

[uart2]
uart_used = 0
uart_type = 4
uart_tx = port:PB00<2><1><default><default>
uart_rx = port:PB01<2><1><default><default>
uart_rts = port:PB02<2><1><default><default>
uart_cts = port:PB03<2><1><default><default>

[uart3]
uart_used = 0
uart_type = 4
uart_tx = port:PH06<3><1><default><default>
uart_rx = port:PH07<3><1><default><default>
uart_rts = port:PH08<3><1><default><default>
uart_cts = port:PH09<3><1><default><default>

[uart4]
uart_used = 0
uart_port = 4
uart_type = 2
uart_tx = port:PA04<2><1><default><default>
uart_rx = port:PA05<2><1><default><default>
uart_rts = port:PA06<2><1><default><default>
uart_cts = port:PA07<2><1><default><default>

[spi0]
spi_used = 0
spi_cs_bitmap = 1
spi_mosi = port:PC00<3><default><default><default>
spi_miso = port:PC01<3><default><default><default>
spi_sclk = port:PC02<3><default><default><default>
spi_cs0 = port:PC03<3><1><default><default>

[spi1]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PA00<2><1><default><default>
spi_sclk = port:PA01<2><default><default><default>
spi_mosi = port:PA02<2><default><default><default>
spi_miso = port:PA03<2><default><default><default>

[spi_devices]
spi_dev_num = 0

[spi_board0]
modalias = "at25df641"
max_speed_hz = 50000000
bus_num = 0
chip_select = 0
mode = 0

[ctp_para]
ctp_used = 1
ctp_twi_id = 0
ctp_twi_addr = 0x5d
ctp_screen_max_x = 768
ctp_screen_max_y = 1024
ctp_revert_x_flag = 0
ctp_revert_y_flag = 0
ctp_exchange_x_y_flag = 0
ctp_gslX680_new = 1
ctp_cob_gslX680 = 7911
ctp_cob_gt9xxf = 7912
ctp_int_port = port:PB05<4><default><default><default>
ctp_wakeup = port:PH01<1><default><default><1>
ctp_power_ldo = "axp22_ldoio1"
ctp_power_ldo_vol = 3300
ctp_power_io =

[ctp_list_para]
ctp_det_used = 1
ft5x_ts = 1
gt82x = 1
gslX680 = 0
gslX680new = 1
gt9xx_ts = 0
gt9xxf_ts = 1
tu_ts = 0
gt818_ts = 1
zet622x = 0
aw5306_ts = 0
icn83xx_ts = 0

[tkey_para]
tkey_used = 0
tkey_twi_id =
tkey_twi_addr =
tkey_int =

[motor_para]
motor_used = 0
motor_shake = port:power3<1><default><default><1>
motor_ldo = ""
motor_ldo_voltage = 3300

[ths_para]
ths_used = 1
ths_trip1_count = 3
ths_trip1_0 = 75
ths_trip1_1 = 90
ths_trip1_2 = 110
ths_trip1_0_min = 0
ths_trip1_0_max = 1
ths_trip1_1_min = 1
ths_trip1_1_max = 3
ths_trip1_2_min = 0
ths_trip1_2_max = 0

[cooler_table]
cooler_count = 4
cooler0 = "1344000 4 4294967295 0"
cooler1 = "1200000 4 4294967295 0"
cooler2 = "1008000 4 4294967295 0"
cooler3 = "648000 4 4294967295 0"

[nand0_para]
nand_support_2ch = 0
nand0_used = 1
nand0_we = port:PC00<2><default><default><default>
nand0_ale = port:PC01<2><default><default><default>
nand0_cle = port:PC02<2><default><default><default>
nand0_ce1 = port:PC03<2><default><default><default>
nand0_ce0 = port:PC04<2><default><default><default>
nand0_nre = port:PC05<2><default><default><default>
nand0_rb0 = port:PC06<2><default><default><default>
nand0_rb1 = port:PC07<2><default><default><default>
nand0_d0 = port:PC08<2><default><default><default>
nand0_d1 = port:PC09<2><default><default><default>
nand0_d2 = port:PC10<2><default><default><default>
nand0_d3 = port:PC11<2><default><default><default>
nand0_d4 = port:PC12<2><default><default><default>
nand0_d5 = port:PC13<2><default><default><default>
nand0_d6 = port:PC14<2><default><default><default>
nand0_d7 = port:PC15<2><default><default><default>
nand0_ndqs = port:PC16<2><default><default><default>
nand0_ce2 = port:PC17<2><default><default><default>
nand0_ce3 = port:PC18<2><default><default><default>
id_number_ctl = 2
nand_p1 = 131094

[disp_init]
disp_init_enable = 1
disp_mode = 0
screen0_output_type = 1
screen0_output_mode = 4
screen1_output_type = 1
screen1_output_mode = 4
fb0_format = 10
fb0_pixel_sequence = 0
fb0_scaler_mode_enable = 0
fb0_width = 0
fb0_height = 0
fb1_format = 10
fb1_pixel_sequence = 0
fb1_scaler_mode_enable = 0
fb1_width = 0
fb1_height = 0
lcd0_backlight = 197
lcd1_backlight = 197
lcd0_bright = 50
lcd0_contrast = 50
lcd0_saturation = 57
lcd0_hue = 50
lcd1_bright = 50
lcd1_contrast = 50
lcd1_saturation = 57
lcd1_hue = 50

[lcd0_para]
lcd_used = 1
lcd_driver_name = "default_lcd"
lcd_if = 3
lcd_x = 768
lcd_y = 1024
lcd_width = 120
lcd_height = 160
lcd_dclk_freq = 70
lcd_pwm_used = 1
lcd_pwm_ch = 0
lcd_pwm_freq = 50000
lcd_pwm_pol = 1
lcd_hbp = 80
lcd_ht = 928
lcd_hspw = 10
lcd_vbp = 23
lcd_vt = 1065
lcd_vspw = 10
lcd_lvds_if = 0
lcd_lvds_colordepth = 0
lcd_lvds_mode = 0
lcd_frm = 0
lcd_gamma_en = 0
lcd_bright_curve_en = 0
lcd_cmap_en = 0
deu_mode = 0
lcdgamma4iep = 22
smart_color = 90
lcd_bl_en = port:PH06<1><0><default><1>
lcd_power = port:power2<1><0><default><1>
lcd_gpio_0 = port:PH07<1><0><default><0>
lcdd0 = port:PD18<3><0><default><default>
lcdd1 = port:PD19<3><0><default><default>
lcdd2 = port:PD20<3><0><default><default>
lcdd3 = port:PD21<3><0><default><default>
lcdd4 = port:PD22<3><0><default><default>
lcdd5 = port:PD23<3><0><default><default>
lcdd6 = port:PD24<3><0><default><default>
lcdd7 = port:PD25<3><0><default><default>
lcdd8 = port:PD26<3><0><default><default>
lcdd9 = port:PD27<3><0><default><default>

[pwm0_para]
pwm_used = 1
pwm_positive = port:PH00<2><0><default><default>

[pwm1_para]
pwm_used = 0
pwm_positive = port:PH01<2><0><default><default>

[csi0]
vip_used = 1
vip_mode = 0
vip_dev_qty = 2
vip_define_sensor_list = 0
vip_csi_pck = port:PE00<2><default><default><default>
vip_csi_mck = port:PE01<2><default><default><default>
vip_csi_hsync = port:PE02<2><default><default><default>
vip_csi_vsync = port:PE03<2><default><default><default>
vip_csi_d0 = port:PE04<2><default><default><default>
vip_csi_d1 = port:PE05<2><default><default><default>
vip_csi_d2 = port:PE06<2><default><default><default>
vip_csi_d3 = port:PE07<2><default><default><default>
vip_csi_d4 = port:PE08<2><default><default><default>
vip_csi_d5 = port:PE09<2><default><default><default>
vip_csi_d6 = port:PE10<2><default><default><default>
vip_csi_d7 = port:PE11<2><default><default><default>
vip_dev0_mname = "gc2035"
vip_dev0_pos = "rear"
vip_dev0_lane = 1
vip_dev0_twi_id = 2
vip_dev0_twi_addr = 120
vip_dev0_isp_used = 0
vip_dev0_fmt = 0
vip_dev0_stby_mode = 0
vip_dev0_vflip = 0
vip_dev0_hflip = 0
vip_dev0_iovdd = "axp22_dldo3"
vip_dev0_iovdd_vol = 2800000
vip_dev0_avdd = "axp22_ldoio0"
vip_dev0_avdd_vol = 2800000
vip_dev0_dvdd = "axp22_eldo2"
vip_dev0_dvdd_vol = 1800000
vip_dev0_afvdd = "axp22_eldo3"
vip_dev0_afvdd_vol = 2800000
vip_dev0_power_en =
vip_dev0_reset = port:PE16<1><1><default><0>
vip_dev0_pwdn = port:PE15<1><1><default><1>
vip_dev0_flash_en =
vip_dev0_flash_mode =
vip_dev0_af_pwdn =
vip_dev1_mname = "gc0308"
vip_dev1_pos = "front"
vip_dev1_lane = 1
vip_dev1_twi_id = 2
vip_dev1_twi_addr = 66
vip_dev1_isp_used = 0
vip_dev1_fmt = 0
vip_dev1_stby_mode = 0
vip_dev1_vflip = 0
vip_dev1_hflip = 0
vip_dev1_iovdd = "axp22_dldo3"
vip_dev1_iovdd_vol = 2800000
vip_dev1_avdd = "axp22_ldoio0"
vip_dev1_avdd_vol = 2800000
vip_dev1_dvdd = "axp22_eldo2"
vip_dev1_dvdd_vol = 1800000
vip_dev1_afvdd = "axp22_eldo3"
vip_dev1_afvdd_vol = 2800000
vip_dev1_power_en =
vip_dev1_reset = port:PE16<1><1><default><0>
vip_dev1_pwdn = port:PE17<1><1><default><1>
vip_dev1_flash_en =
vip_dev1_flash_mode =
vip_dev1_af_pwdn =

[camera_list_para]
camera_list_para_used = 1
ov7670 = 0
hi704 = 0
mt9m112 = 0
mt9m113 = 0
ov2655 = 0
hi253 = 0
gc0307 = 0
mt9d112 = 0
ov5647 = 0
gc2015 = 0
ov2643 = 0
tvp5150 = 0
s5k4ec = 0
ov5650_mv9335 = 0
siv120d = 1
siv121d = 1
gc0309 = 1
gc0308 = 1
gc0311 = 1
gc0328 = 1
gc0329 = 1
sp0838 = 1
sp0718 = 1
sp0a19 = 1
bf3a03 = 1
bf3703 = 1
sp2518 = 1
gc2035 = 1
gc2155 = 1
gc2145 = 1
bf3920 = 1
st25a = 1
gt2005 = 1
ov5640 = 1

[mmc0_para]
sdc_used = 1
sdc_detmode = 2
sdc_buswidth = 4
sdc_d1 = port:PF00<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>
sdc_det = port:PB04<4><1><2><default>
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"

[mmc1_para]
sdc_used = 1
sdc_detmode = 4
sdc_buswidth = 4
sdc_clk = port:PG00<2><1><1><default>
sdc_cmd = port:PG01<2><1><1><default>
sdc_d0 = port:PG02<2><1><1><default>
sdc_d1 = port:PG03<2><1><1><default>
sdc_d2 = port:PG04<2><1><1><default>
sdc_d3 = port:PG05<2><1><1><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 1
sdc_regulator = "none"

[mmc2_para]
sdc_used = 0
sdc_detmode = 3
sdc_buswidth = 8
sdc_2xmode = 1
sdc_clk = port:PC05<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>
sdc_d4 = port:PC12<3><1><2><default>
sdc_d5 = port:PC13<3><1><2><default>
sdc_d6 = port:PC14<3><1><2><default>
sdc_d7 = port:PC15<3><1><2><default>
emmc_rst = port:PC16<3><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"

[usbc0]
usb_used = 1
usb_port_type = 2
usb_detect_type = 1
usb_id_gpio = port:PH08<0><1><default><default>
usb_det_vbus_gpio = "axp_ctrl"
usb_drv_vbus_gpio = port:power4<1><0><default><0>
usb_restrict_gpio =
usb_host_init_state = 0
usb_restric_flag = 0
usb_restric_voltage = 3550000
usb_restric_capacity = 5
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_regulator_id_vbus = "axp22_dcdc1"
usb_regulator_id_vbus_vol = 3000000

[usbc1]
usb_used = 0
usb_drv_vbus_gpio =
usb_restrict_gpio =
usb_host_init_state = 0
usb_restric_flag = 0
usb_regulator_io = "nocare"
usb_regulator_vol = 0
usb_not_suspend = 0

[usb_feature]
vendor_id = 7994
mass_storage_id = 4096
adb_id = 4097
manufacturer_name = "USB Developer"
product_name = "Android"
serial_number = "20080411"

[msc_feature]
vendor_name = "USB 2.0"
product_name = "USB Flash Driver"
release = 100
luns = 2

[serial_feature]
serial_unique = 1

[gsensor_para]
gsensor_used = 1
gsensor_twi_id = 1
gsensor_twi_addr = 0x18
gsensor_int1 =
gsensor_int2 =

[gsensor_list_para]
gsensor_det_used = 1
bma250 = 1
stk831x = 0
mma8452 = 1
mma7660 = 1
mma865x = 1
mc32x0 = 0
afa750 = 1
lis3de_acc = 1
lis3dh_acc = 1
kxtik = 1
dmard10 = 0
dmard06 = 1
mxc622x = 1
fxos8700 = 1
lsm303d = 1

[gps_para]

[wifi_para]
wifi_used = 1
wifi_sdc_id = 1
wifi_usbc_id = 1
wifi_usbc_type = 1
wifi_mod_sel = 8
wifi_power = "axp22_dldo1"
wifi_power_ext1 = "axp22_dldo2"
wifi_power_ext2 = ""
wifi_power_switch = ""
rtl8189es_shdn = port:PL06<1><default><default><0>
rtl8189es_host_wake = port:PL07<4><default><default><1>

[bt_para]
bt_used = 0
bt_uart_id = 1

[3g_para]
3g_used = 0
3g_usbc_num = 1
3g_uart_num = 2
bb_name = "em66"
bb_vbat =
bb_on =
bb_pwr_on = port:PL03<1><default><default><0>
bb_wake = port:PL04<1><default><default><0>
bb_rf_dis = port:PL11<1><default><default><0>
bb_rst = port:PL05<1><default><default><0>
bb_dldo = "axp22_aldo1"
bb_dldo_min_uV = 2800000
bb_dldo_max_uV = 2800000

[gy_para]
gy_used = 0
gy_twi_id = 1
gy_twi_addr = 106
gy_int1 =
gy_int2 =

[gy_list_para]
gy_det_used = 1
l3gd20_gyr = 1

[ls_para]
ls_used = 0
ls_twi_id = 1
ls_twi_addr = 35
ls_int = port:PB07<4><1><default><default>

[ls_list_para]
ls_det_used = 1
ltr_501als = 1
jsa1212 = 1

[compass_para]
compass_used = 0
compass_twi_id = 1
compass_twi_addr = 13
compass_int =

[i2s0]
i2s0_used = 0
i2s0_channel = 2
i2s0_master = 4
i2s0_select = 1
audio_format = 1
signal_inversion = 1
over_sample_rate = 512
sample_resolution = 16
word_select_size = 32
pcm_sync_period = 256
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 16
frame_width = 1
tx_data_mode = 1
rx_data_mode = 1
i2s0_mclk =
i2s0_bclk = port:PB04<2><1><default><default>
i2s0_lrclk = port:PB05<2><1><default><default>
i2s0_dout0 = port:PB06<2><1><default><default>
i2s0_dout1 =
i2s0_dout2 =
i2s0_dout3 =
i2s0_din = port:PB07<2><1><default><default>

[i2s1]
i2s1_used = 0
i2s1_channel = 2
i2s1_master = 4
i2s1_select = 1
audio_format = 1
signal_inversion = 1
over_sample_rate = 512
sample_resolution = 16
word_select_size = 32
pcm_sync_period = 64
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 16
frame_width = 1
tx_data_mode = 0
rx_data_mode = 0
i2s1_mclk =
i2s1_bclk = port:PG11<2><1><default><default>
i2s1_lrclk = port:PG10<2><1><default><default>
i2s1_dout = port:PG12<2><1><default><default>
i2s1_din = port:PG13<2><1><default><default>

[audio0]
audio_used = 1
headphone_vol = 59
earpiece_vol = 59
cap_vol = 5
pa_single_vol = 61
pa_double_used = 1
pa_double_vol = 61
headphone_direct_used = 0
headset_mic_vol = 6
main_mic_vol = 6
audio_hp_ldo = "none"
audio_pa_ctrl = port:PH09<1><default><default><0>
aif2_used = 0
aif3_used = 0
headphone_mute_used = 0
DAC_VOL_CTRL_SPK = 41120
DAC_VOL_CTRL_HEADPHONE = 41120
agc_used = 0
drc_used = 0

[pmu1_para]
pmu_used = 1
pmu_twi_addr = 52
pmu_twi_id = 1
pmu_irq_id = 0
pmu_battery_rdc = 116
pmu_battery_cap = 3540
pmu_batdeten = 1
pmu_chg_ic_temp = 0
pmu_runtime_chgcur = 450
pmu_earlysuspend_chgcur = 1200
pmu_suspend_chgcur = 1500
pmu_shutdown_chgcur = 1500
pmu_init_chgvol = 4200
pmu_init_chgend_rate = 15
pmu_init_chg_enabled = 1
pmu_init_adc_freq = 800
pmu_init_adcts_freq = 800
pmu_init_chg_pretime = 70
pmu_init_chg_csttime = 720
pmu_batt_cap_correct = 1
pmu_bat_regu_en = 0
pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 0
pmu_bat_para5 = 0
pmu_bat_para6 = 0
pmu_bat_para7 = 0
pmu_bat_para8 = 0
pmu_bat_para9 = 1
pmu_bat_para10 = 1
pmu_bat_para11 = 1
pmu_bat_para12 = 2
pmu_bat_para13 = 2
pmu_bat_para14 = 7
pmu_bat_para15 = 13
pmu_bat_para16 = 19
pmu_bat_para17 = 23
pmu_bat_para18 = 27
pmu_bat_para19 = 33
pmu_bat_para20 = 39
pmu_bat_para21 = 44
pmu_bat_para22 = 46
pmu_bat_para23 = 54
pmu_bat_para24 = 60
pmu_bat_para25 = 66
pmu_bat_para26 = 71
pmu_bat_para27 = 76
pmu_bat_para28 = 81
pmu_bat_para29 = 86
pmu_bat_para30 = 90
pmu_bat_para31 = 95
pmu_bat_para32 = 100
pmu_usbvol_limit = 0
pmu_usbcur_limit = 0
pmu_usbvol = 4000
pmu_usbcur = 0
pmu_usbvol_pc = 4400
pmu_usbcur_pc = 500
pmu_pwroff_vol = 3300
pmu_pwron_vol = 2600
pmu_pekoff_time = 6000
pmu_pekoff_func = 0
pmu_pekoff_en = 1
pmu_peklong_time = 1500
pmu_pekon_time = 1000
pmu_pwrok_time = 64
pmu_battery_warning_level1 = 15
pmu_battery_warning_level2 = 0
pmu_restvol_adjust_time = 60
pmu_ocv_cou_adjust_time = 60
pmu_chgled_func = 0
pmu_chgled_type = 0
pmu_vbusen_func = 1
pmu_reset = 0
pmu_IRQ_wakeup = 0
pmu_hot_shutdowm = 1
pmu_inshort = 0
power_start = 0
pmu_temp_enable = 1
pmu_charge_ltf = 2261
pmu_charge_htf = 388
pmu_discharge_ltf = 3200
pmu_discharge_htf = 237
pmu_temp_para1 = 7466
pmu_temp_para2 = 4480
pmu_temp_para3 = 3518
pmu_temp_para4 = 2786
pmu_temp_para5 = 2223
pmu_temp_para6 = 1788
pmu_temp_para7 = 1448
pmu_temp_para8 = 969
pmu_temp_para9 = 664
pmu_temp_para10 = 466
pmu_temp_para11 = 393
pmu_temp_para12 = 333
pmu_temp_para13 = 283
pmu_temp_para14 = 242
pmu_temp_para15 = 179
pmu_temp_para16 = 134

[pmu2_para]
pmu_used = 0
pmu_twi_addr = 52
pmu_twi_id = 1
pmu_irq_id = 0

[recovery_key]
key_min = 2
key_max = 100

[dvfs_table]
extremity_freq = 1344000000
max_freq = 1200000000
min_freq = 120000000
LV_count = 8
LV1_freq = 1536000000
LV1_volt = 1500
LV2_freq = 1344000000
LV2_volt = 1460
LV3_freq = 1200000000
LV3_volt = 1320
LV4_freq = 1008000000
LV4_volt = 1200
LV5_freq = 816000000
LV5_volt = 1100
LV6_freq = 648000000
LV6_volt = 1040
LV7_freq = 0
LV7_volt = 1040
LV8_freq = 0
LV8_volt = 1040

[Vdevice]
Vdevice_used = 1
Vdevice_0 = port:PA01<5><1><2><default>
Vdevice_1 = port:PA02<5><1><2><default>

[s_uart0]
s_uart_used = 0
s_uart_tx = port:PL02<2><default><default><default>
s_uart_rx = port:PL03<2><default><default><default>

[s_rsb0]
s_rsb_used = 1
s_rsb_sck = port:PL00<2><1><2><default>
s_rsb_sda = port:PL01<2><1><2><default>

[s_jtag0]
s_jtag_used = 0
s_jtag_tms = port:PL04<2><1><2><default>
s_jtag_tck = port:PL05<2><1><2><default>
s_jtag_tdo = port:PL06<2><1><2><default>
s_jtag_tdi = port:PL07<2><1><2><default>

[s_powchk]
s_powchk_used = -2147483648
s_power_reg = 32865
s_system_power = 50

[mali_para]
mali_used = 1
mali_clkdiv = 1
mali_extreme_freq = 408
mali_extreme_vol = 1100

[dram_dvfs_table]
LV_count = 3
LV1_freq = 552000000
LV1_volt = 1100
LV2_freq = 360000000
LV2_volt = 1100
LV3_freq = 0
LV3_volt = 1100

[charging_type]
charging_type = 1

[dram_scene_table]
LV_count = 3
LV1_scene = 1
LV1_freq = 360000000
LV2_scene = 2
LV2_freq = 240000000
LV3_scene = 3
LV3_freq = 168000000

;---------------------------------------------------------------------------------------------------------
; 说明： 脚本中的字符串区分大小写，用户可以修改"="后面的数值，但是不要修改前面的字符串
;---------------------------------------------------------------------------------------------------------


;--------------------------------------------------------------------------------------------------
; 固件下载参数配置
;--------------------------------------------------------------------------------------------------
;****************************************************
; mbr的大小, 以Kbyte为单位
;****************************************************
[mbr]
size = 16384

;********************************************************************************************************
; 分区配置
;
;
; partition 定义范例:
; [partition] ; //表示是一个分区
; name = USERFS2 ; //分区名称
; size = 16384 ; //分区大小 单位: 扇区.分区表示个数最多2^31 * 512 = 2T
; downloadfile = "123.fex" ; //下载文件的路径和名称，可以使用相对路径，相对是指相对于image.cfg文件所在分区。也可以使用绝对路径
; keydata = 1 ; //私有数据分区，重新量产数据将不丢失
; encrypt = 1 ; //采用加密方式烧录，将提供数据加密，但损失烧录速度
; = ? ; //私有用法
; verify = 1 ; //要求量产完成后校验是否正确
;
; 注：1、name唯一, 不允许同名
; 2、name最大12个字符
; 3、size = 0, 将创建一个无大小的空分区
; 4、为了安全和效率考虑，分区大小最好保证为16M字节的整数倍
;********************************************************************************************************
[partition_start]

;------------------------------>mmcblk0p2/nanda
[partition]
name = bootloader
size = 65536
downloadfile = "boot-resource.fex"
user_type = 0x8000

;------------------------------>mmcblk0p5/nandb
[partition]
name = env
size = 32768
downloadfile = "env.fex"
user_type = 0x8000

;------------------------------>mmcblk0p6/nandc
[partition]
name = boot
size = 32768
downloadfile = "boot.fex"
user_type = 0x8000

;------------------------------>mmcblk0p7/nandd
[partition]
name = system
size = 1572864
downloadfile = "system.fex"
user_type = 0x8000

;------------------------------>mmcblk0p8/nande
[partition]
name = data
size = 2097152
user_type = 0x8000

;------------------------------>mmcblk0p9/nandf
[partition]
name = misc
size = 32768
user_type = 0x8000

;------------------------------>mmcblk0p10/nandg
[partition]
name = recovery
size = 65536
downloadfile = "recovery.fex"
user_type = 0x8000

;------------------------------>mmcblk0p11/nandh
[partition]
name = cache
size = 262144
user_type = 0x8000

;------------------------------>nandi, data image backup
[partition]
name = databk
size = 262144
user_type = 0x8000

;------------------------------>nandj, data image private
[partition]
name = private
size = 32768
ro = 0
user_type = 0x8000

;------------------------------>nandk, UDISK
[partition]
name = UDISK
user_type = 0x8100
downloadfile = "diskfs.fex"
verify = 0

AdbDriverInstaller.exe ( 9 МБ )
adb nand.rar ( 240.32 КБ )

ползуйтесь на здоровье =)

kernel - если правильно понял то это само ядро (Ядро состоит из набора драйверов всего имеющегося в устройстве оборудования и подсистемы управления памятью, сетью, безопасностью, и прочих основных функций операционной системы.)
ramdisk он же и initrd.gz - лежит в буте и рекавери, в них нужные модули и всякая начинка по типу init.rc,init.sun8i.rc,fstab.sun8i и т д...(в буте свой рамдиск а в рекавери свой)

что бы посмотреть
adb shell cat /proc/partitions (adb shell cat /proc/cmdline),(adb shell ls -l /dev/block/by-name)
или
cat /proc/partitions (cat /proc/cmdline),(ls -l /dev/block/by-name)

nanda - bootloader
nandb - env
nandc - boot
nandd - system
nande - data (не нужен)
nandf - misc
nandg - recovery
nandh - cache (не нужен)
nandi - metadata
nandj - private
nandk - UDISK (не нужен)

PSYZuM, тут драйвера выложил
вот подправил батник и добавил кое что adb nand.rar ( 1.86 МБ )


adb root
adb remount
adb shell cat /proc/partitions
adb shell "cat /mnt/sdcard/nanda > /dev/block/nanda; sync"
adb shell "cat /mnt/sdcard/nandb > /dev/block/nandb; sync"
adb shell "cat /mnt/sdcard/nandc > /dev/block/nandc; sync"
adb shell "cat /mnt/sdcard/nande > /dev/block/nande; sync"
adb shell "cat /mnt/sdcard/nandf > /dev/block/nandf; sync"
adb shell "cat /mnt/sdcard/nandg > /dev/block/nandg; sync"
adb shell "cat /mnt/sdcard/nandh > /dev/block/nandh; sync"
adb shell "cat /mnt/sdcard/nandi > /dev/block/nandi; sync"
adb shell "cat /mnt/sdcard/nandj > /dev/block/nandj; sync"
adb shell "cat /mnt/sdcard/nandd > /dev/block/nandd; sync"

adb root
adb remount
adb shell cat /proc/partitions
adb shell su -c "dd if=/mnt/sdcard/nanda of=/dev/block/nanda"
adb shell su -c "dd if=/mnt/sdcard/nandb of=/dev/block/nandb"
adb shell su -c "dd if=/mnt/sdcard/nandc of=/dev/block/nandc"
adb shell su -c "dd if=/mnt/sdcard/nande of=/dev/block/nande"
adb shell su -c "dd if=/mnt/sdcard/nandf of=/dev/block/nandf"
adb shell su -c "dd if=/mnt/sdcard/nandg of=/dev/block/nandg"
adb shell su -c "dd if=/mnt/sdcard/nandh of=/dev/block/nandh"
adb shell su -c "dd if=/mnt/sdcard/nandi of=/dev/block/nandi"
adb shell su -c "dd if=/mnt/sdcard/nandj of=/dev/block/nandj"
adb shell su -c "dd if=/mnt/sdcard/nandd of=/dev/block/nandd"

или через консоль андроида или подобных... SH Script Ru
cat /mnt/sdcard/nandd > /dev/block/nandd; sync

dd if=/mnt/sdcard/nandd of=/dev/block/nandd
вот только не знаю как андроид перезаписует систем(нандд) если команды берёт от нее же..возможно что могут быть ошибки,но я не знаю