UnieLec U7621-06 – прошивка [open-wrt (pandora v.14), padavan] | Wi-Fi Router: 300Mb\s - 867Mb\s + 5x1Gb | 1, PCI-E:3, SATA:1, SD:1



Реп: (1390)
UnieLec U7621-06 [open-wrt (pandora v.14), padavan] – прошивка »
Wi-Fi Router: 2.4GHz(300Mbit\s) - 5GHz(867Mbit\s) + 5•1Gbit\s | USB:1, PCI-E:3, SATA:1, SD:1


Прикрепленное изображение
Описание
Сабж подойдет для тех, кто не боится сам поработать немного руками и "напильником", как говорится для души.

Плюсы и минусы:
Модульная система, позволяет делать апгрейд радио части (единственный на рынке с тремя PCI-E слотами в данной категории).
Не очень презентабелный корпус с плохим теплоотведением зато полностью металлический, нету радиаторов на чипах;
Малоизвестный производитель.
Дополнительные изображения
Прикрепленное изображение
Прикрепленное изображение
Прикрепленное изображение
Технические характеристики
  • Процессор: MT7621AT 2х880MHz;
  • ПЗУ: 16 MB SPI Flash (возможно расширение до 32 МБ или замена на Nand flash);
  • ОЗУ: 256 MB DDR3 (возможно расширение до 512 MB DDR3);
  • 2.4 Ghz WiFi 2x2 (до 300 Мбит/сек);
  • 5.7 Ghz WiFi 2x2 (до 867 Мбит/сек);
  • 1хSATA;
  • 3хPCI-E (Два занято под WIFI модули);
  • 1хMicroSD;
  • 30xGPIO;
  • WAN (до 1000 Мбит/сек);
  • LAN х4 (до 1000 Мбит/сек);
  • Внешние ненаправленные антенны - 4 шт;
  • Модули WIFI опционально.
Полезная информация
На данный момент кастомных прошивок нет, все в процессе...
Офицеальный магазин на aliexpress.
Сайт производителя www.unielecinc.com.
Лог загрузки
Прошивка


В теме нет куратора. По вопросам наполнения шапки обращайтесь к автору в QMS или к модераторам раздела через кнопку Изображение под сообщениями. Как это сделать правильно, что бы вас поняли с первого раза, хорошо описано здесь.

Сообщение отредактировал Freize - 15.11.18, 10:41
Причина редактирования: Стоковая прошивка



Реп: (1390)
Из того что пока знаю:
1. Светодиоды хардварные.
2. Кнопка ресет софтовая на 18-м GPIO.
3. Разметка флеш памяти стандартная.
4. PCI-E разведены на два чипа справа на плате, и еще один на SATA. Третий PCI-E, который слева это выход USB2.
5. На борту U-Boot версии 4.0, восстановление с UART поддерживается, веб морды нет, режима восстановления нет.
6. Прошивка Pandora Box v.14, ядро Linux version 3.14.48.
7. Ланы:
WAN=4
LAN1=3
LAN2=2
LAN3=1
LAN4=0

Лог загрузки:
BusyBox v1.22.1 (2015-07-13 22:20:58 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______________________________________________________________
| ____ _ ____ |
| | _ \ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ |
| | |_) / _` | '_ \ / _` |/ _ \| '__/ _` | _ \ / _ \ \/ / |
| | __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < |
| |_| \__,_|_| |_|\__,_|\___/|_| \__,_|____/ \___/_/\_\ |
| |
| PandoraBox SDK Platform |
| The Core of SmartRouter |
| Copyright 2013-2015 D-Team Technology Co.,Ltd.SZ |
| http://www.pandorabox.org.cn |
|______________________________________________________________|
Base on OpenWrt BARRIER BREAKER (14.09, r1180)
[root@PandoraBox_807B:/root]#dmesgdmesg
[ 0.000000] Linux version 3.14.48 (lintel@PandoraBox-Server) (gcc version 4.8.3 (PandoraBox/Linaro GCC 4.8-2014.04 r972) ) #8 SMP Tue Jul 14 14:56:52 CST 2015
[ 0.000000] MT7621: MPLL enabled.
[ 0.000000] PandoraBox CPUID Module for Ralink/MTK SoC v1.1.
[ 0.000000] MediaTek MT7621 pkg:BGA rev:1 eco:3 CPU:880MHz, Bus:220MHz Uart:50MHz
[ 0.000000] CPU running in Little Endian
[ 0.000000] Board VLAN:LLLLW
[ 0.000000] Flash:SPI Size: 16MB
[ 0.000000] DRAM: 256MB DDR3 16 bits
[ 0.000000] Kernel Support [PCI] [USB]
[ 0.000000] prom memory:256MB
[ 0.000000] GCMP present
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x0fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x0fffffff]
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat 8033ff80, node_mem_map 81000000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] Detected 3 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s5696 r8192 d14784 u32768
[ 0.000000] pcpu-alloc: s5696 r8192 d14784 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: pause_on_oops=10 noresume board=PBR-M1 console=ttyS1,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00020c04
[ 0.000000] Readback ErrCtl register=00020c04
[ 0.000000] Memory: 255836K/262144K available (2736K kernel code, 135K rwdata, 516K rodata, 184K init, 289K bss, 6308K reserved, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:256
[ 0.000000] GIC: Revision 3.0
[ 0.000000] Setup MT7621 IRQs...Done
[ 0.000000] console [ttyS1] enabled
[ 0.000000] bootconsole [early0] disabled
[ 0.010000] Calibrating delay loop... 580.40 BogoMIPS (lpj=2902016)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] CPU1 :Booting up...done!
[ 0.090000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.090000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.090000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.090000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.150000] Synchronize counters for CPU 1: done.
[ 0.160000] CPU2 :Booting up...done!
[ 0.160000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.160000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.160000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.160000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.220000] Synchronize counters for CPU 2: done.
[ 0.230000] CPU3 :Booting up...done!
[ 0.230000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.230000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.230000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.230000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.280000] Synchronize counters for CPU 3: done.
[ 0.300000] Brought up 4 CPUs
[ 0.300000] pinctrl core: initialized pinctrl subsystem
[ 0.310000] NET: Registered protocol family 16
[ 0.310000] Ralink/MTK BootROM maped.
[ 0.320000] Generic GPIO Driver for MediaTek MT7621 Board. (c) 2013-2015 PandoraBox Team
[ 0.320000] MT7621-GPIO0:registering 32 irq handlers
[ 0.330000] MT7621-GPIO1:registering 32 irq handlers
[ 0.330000] MT7621-GPIO3:registering 32 irq handlers
[ 0.340000] MIPS: machine is PandoraBox PBR-M1
[ 0.340000] ralink_register_flash:SPI Flash.
[ 0.340000] MT762x:SDHC Interface registered.
[ 0.350000] Ralink/MTK PinCtrl registered.
[ 0.350000] Generic PinCtrl Driver for MediaTek MT7621 Board. (c) 2013-2015 PandoraBox Team
[ 0.360000] PINCTRL:add 31 pins for MT7621-PINCTRL0.
[ 0.360000] PINCTRL:add 31 pins for MT7621-PINCTRL1.
[ 0.370000] PINCTRL:add 31 pins for MT7621-PINCTRL2.
[ 0.370000] GPIO_MODE_REG:0x94A8
[ 1.760000] PCIE0 enabled
[ 1.760000] PCIE1 enabled
[ 1.770000] PCIE2 enabled
[ 1.770000] FPU Affinity set after 11720 emulations
[ 1.780000] bio: create slab <bio-0> at 0
[ 1.780000] PCI host bridge to bus 0000:00
[ 1.790000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.790000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.800000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.800000] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.800000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.800000] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.800000] pci 0000:00:00.0: supports D1
[ 1.800000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.800000] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.800000] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.800000] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.800000] pci 0000:00:01.0: supports D1
[ 1.800000] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.800000] pci 0000:00:02.0: [0e8d:0801] type 01 class 0x060400
[ 1.800000] pci 0000:00:02.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.800000] pci 0000:00:02.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.800000] pci 0000:00:02.0: supports D1
[ 1.800000] pci 0000:00:02.0: PME# supported from D0 D1 D3hot
[ 1.800000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.810000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.810000] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.820000] pci 0000:01:00.0: [1b21:0612] type 00 class 0x010601
[ 1.820000] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x0007]
[ 1.820000] pci 0000:01:00.0: reg 0x14: [io 0x0000-0x0003]
[ 1.820000] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x0007]
[ 1.820000] pci 0000:01:00.0: reg 0x1c: [io 0x0000-0x0003]
[ 1.820000] pci 0000:01:00.0: reg 0x20: [io 0x0000-0x001f]
[ 1.820000] pci 0000:01:00.0: reg 0x24: [mem 0x00000000-0x000001ff]
[ 1.820000] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 1.820000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.820000] pci 0000:02:00.0: [14c3:7612] type 00 class 0x028000
[ 1.820000] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.820000] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 1.820000] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 1.820000] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.820000] pci 0000:03:00.0: [14c3:7602] type 00 class 0x028000
[ 1.820000] pci 0000:03:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.820000] pci 0000:03:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 1.820000] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 1.820000] pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 03
[ 1.820000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 03
[ 1.820000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.820000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.830000] pci 0000:00:02.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.830000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.840000] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 1.840000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 1.850000] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[ 1.850000] pci 0000:00:02.0: BAR 8: assigned [mem 0x60400000-0x604fffff]
[ 1.860000] pci 0000:00:02.0: BAR 9: assigned [mem 0x60500000-0x605fffff pref]
[ 1.860000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
[ 1.870000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
[ 1.870000] pci 0000:00:02.0: BAR 1: assigned [mem 0x60620000-0x6062ffff]
[ 1.880000] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 1.880000] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[ 1.890000] pci 0000:01:00.0: BAR 5: assigned [mem 0x60000000-0x600001ff]
[ 1.890000] pci 0000:01:00.0: BAR 4: assigned [io 0x1e160000-0x1e16001f]
[ 1.900000] pci 0000:01:00.0: BAR 0: assigned [io 0x1e160020-0x1e160027]
[ 1.900000] pci 0000:01:00.0: BAR 2: assigned [io 0x1e160028-0x1e16002f]
[ 1.910000] pci 0000:01:00.0: BAR 1: assigned [io 0x1e160030-0x1e160033]
[ 1.910000] pci 0000:01:00.0: BAR 3: assigned [io 0x1e160034-0x1e160037]
[ 1.920000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.920000] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 1.930000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.930000] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 1.940000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
[ 1.940000] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
[ 1.950000] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.950000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.960000] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref]
[ 1.960000] pci 0000:03:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit]
[ 1.970000] pci 0000:03:00.0: BAR 6: assigned [mem 0x60500000-0x6050ffff pref]
[ 1.970000] pci 0000:00:02.0: PCI bridge to [bus 03]
[ 1.980000] pci 0000:00:02.0: bridge window [mem 0x60400000-0x604fffff]
[ 1.980000] pci 0000:00:02.0: bridge window [mem 0x60500000-0x605fffff pref]
[ 1.990000] PCI Bus 1 slot 0 mapping to IRQ4.
[ 1.990000] PCI Bus 2 slot 1 mapping to IRQ24.
[ 1.990000] PCI Bus 3 slot 2 mapping to IRQ25.
[ 2.000000] Switched to clocksource MIPS
[ 2.000000] NET: Registered protocol family 2
[ 2.010000] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.010000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.020000] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.030000] TCP: reno registered
[ 2.030000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.040000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.040000] NET: Registered protocol family 1
[ 2.050000] PCI: CLS 80 bytes, default 32
[ 2.050000] Ralink SoC clocks api init.
[ 2.050000] mips hpt frequency:440000000HZ
[ 2.290000] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.300000] Ralink/MTK APSoC GPIO Resource maped.
[ 2.310000] PandoraBox USB OverCharged driver (c) 2013-2015 PandoraBox Team
[ 2.310000] usb-oc:enable USB2_PWR_CTRL port power
[ 2.320000] usb-oc:enable USB3_PWR_CTRL port power
[ 2.320000] usb-oc:enable SATA3_PWR_CTRL port power
[ 2.330000] Load Kernel WDG Timer Module
[ 2.330000] Load Ralink Timer0 Module
[ 2.330000] Load Ralink Timer2 Module
[ 2.340000] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 2.350000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.350000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.360000] msgmni has been set to 499
[ 2.370000] io scheduler noop registered (default)
[ 2.370000] io scheduler deadline registered
[ 2.380000] io scheduler cfq registered
[ 2.380000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 2.390000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27, base_baud = 3125000) is a 16550A
[ 2.400000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26, base_baud = 3125000) is a 16550A
[ 2.410000] serial8250: ttyS2 at MMIO 0x1e000e00 (irq = 28, base_baud = 3125000) is a 16550A
[ 2.410000] Enable Ralink GDMA Controller Module
[ 2.420000] GDMA IP Version=3
[ 2.430000] brd: module loaded
[ 2.440000] flash manufacture id: c2, device id 20 18
[ 2.440000] MX25L12805D(c2 2018c220) (16384 Kbytes)
[ 2.450000] mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[ 2.460000] Creating 5 MTD partitions on "raspi":
[ 2.460000] 0x000000000000-0x000000030000 : "u-boot"
[ 2.470000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 2.470000] 0x000000040000-0x000000050000 : "Factory"
[ 2.480000] 0x000000000000-0x000001000000 : "fullflash"
[ 2.490000] 0x000000050000-0x000001000000 : "firmware"
[ 2.520000] 3 uimage-fw partitions found on MTD device firmware
[ 2.530000] 0x000000050000-0x00000017ed03 : "kernel"
[ 2.530000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 2.550000] 0x00000017ed03-0x000000fe0000 : "rootfs"
[ 2.550000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 2.560000] mtd: device 6 (rootfs) set to be root filesystem
[ 2.570000] 1 squashfs-split partitions found on MTD device rootfs
[ 2.580000] 0x000000ec0000-0x000000fe0000 : "rootfs_data"
[ 2.580000] 0x000000fe0000-0x000001000000 : "panic_oops"
[ 2.590000] mtdoops: ready 0, 1 (no erase)
[ 2.590000] mtdoops: Attached to MTD device 8
[ 2.590000] rdm_major = 252
[ 2.600000] raeth: frame engine reset
[ 2.600000] raeth: embedded switch reset
[ 2.610000] EEPROM:Read from [Factory] offset 0xe000,length 0x6.
[ 2.620000] fixing up MHWTRAP register - bootloader probably played with it
[ 2.620000] mt762x-gsw switch driver registered
[ 2.630000] mt762x-gsw default vlans:wllll
[ 2.640000] Ralink APSoC Ethernet Driver v3.2.1 (raeth)
[ 2.640000] raeth: PDMA RX ring 256, QDMA TX pool 512. Max packet size 1536
[ 2.650000] TCP: cubic registered
[ 2.650000] TCP: westwood registered
[ 2.660000] TCP: hybla registered
[ 2.660000] TCP: htcp registered
[ 2.660000] NET: Registered protocol family 17
[ 2.670000] Bridge firewalling registered
[ 2.670000] Ebtables v2.0 registered
[ 2.680000] 8021q: 802.1Q VLAN Support v1.8
[ 2.680000] PandoraBox Mass Storage accelerater v1.2
[ 2.690000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[ 2.700000] Freeing unused kernel memory: 184K (80352000 - 80380000)
[ 3.700000] init: Console is alive
[ 7.010000] random: nonblocking pool is initialized
[ 7.810000] usbcore: registered new interface driver usbfs
[ 7.810000] usbcore: registered new interface driver hub
[ 7.820000] usbcore: registered new device driver usb
[ 7.830000] exFAT: Version 1.2.9
[ 7.890000] ufsd: module license 'Commercial product' taints kernel.
[ 7.890000] Disabling lock debugging due to kernel taint
[ 7.910000] ufsd: driver (8.6, Jul 14 2015 13:33:12, LBD=ON, delalloc, ioctl, bdi) loaded at c043e000
[ 7.910000] NTFS (with native replay) support included
[ 7.910000] optimized: speed
[ 7.910000] Built for PandoraBox 2013-12-27
[ 7.910000]
[ 7.930000] PandoraBox Button Driver init
[ 7.940000] Button [reset] mapped to GPIO18 and IRQ67
[ 7.950000] SCSI subsystem initialized
[ 7.970000] libata version 3.00 loaded.
[ 7.970000] ahci 0000:01:00.0: version 3.0
[ 7.970000] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled
[ 7.980000] ahci 0000:01:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 7.980000] ahci 0000:01:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs
[ 8.000000] scsi0 : ahci
[ 8.000000] scsi1 : ahci
[ 8.000000] ata1: SATA max UDMA/133 abar m512@0x60000000 port 0x60000100 irq 4
[ 8.010000] ata2: SATA max UDMA/133 abar m512@0x60000000 port 0x60000180 irq 4
[ 8.390000] ata1: SATA link down (SStatus 0 SControl 300)
[ 8.740000] ata2: SATA link down (SStatus 0 SControl 300)
[ 8.860000] MT7621 XHCI/EHCI Frequency Calibration start!
[ 8.880000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 8.900000] FM_OUT value: u4FmOut = 291(0x00000123)
[ 8.900000] FM detection done! loop = 1
[ 8.920000] SR calibration value u1SrCalVal = 2
[ 8.920000] MT7621 XHCI/EHCI Frequency Calibration start!
[ 8.940000] FM_OUT value: u4FmOut = 286(0x0000011E)
[ 8.940000] FM detection done! loop = 0
[ 8.960000] SR calibration value u1SrCalVal = 3
[ 8.960000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 8.960000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
[ 8.970000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000
[ 8.980000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.990000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.990000] usb usb1: Product: xHCI Host Controller
[ 9.000000] usb usb1: Manufacturer: Linux 3.14.48 xhci-hcd
[ 9.000000] usb usb1: SerialNumber: xhci-hcd
[ 9.010000] hub 1-0:1.0: USB hub found
[ 9.010000] hub 1-0:1.0: 2 ports detected
[ 9.020000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 9.020000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
[ 9.030000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 9.040000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.040000] usb usb2: Product: xHCI Host Controller
[ 9.050000] usb usb2: Manufacturer: Linux 3.14.48 xhci-hcd
[ 9.050000] usb usb2: SerialNumber: xhci-hcd
[ 9.060000] hub 2-0:1.0: USB hub found
[ 9.060000] hub 2-0:1.0: 1 port detected
[ 9.120000] mtk-sd: MediaTek MT76xx MSDC Driver
[ 9.130000] usbcore: registered new interface driver usb-storage
[ 9.820000] init: - preinit -
[ 13.210000] mount_root: loading kmods from internal overlay
[ 13.620000] jffs2: notice: (358) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (2 unchecked, 0 orphan) and 45 of xref (0 dead, 9 orphan) found.
[ 13.640000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 13.650000] block: unable to load configuration (fstab: Entry not found)
[ 13.650000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 13.660000] block: extroot: not configured
[ 13.760000] jffs2: notice: (355) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (2 unchecked, 0 orphan) and 45 of xref (0 dead, 9 orphan) found.
[ 14.000000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 14.010000] block: unable to load configuration (fstab: Entry not found)
[ 14.020000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 14.030000] block: extroot: not configured
[ 14.070000] mount_root: switching to jffs2 overlay
[ 14.080000] procd: - early -
[ 14.820000] procd: - ubus -
[ 15.840000] procd: - init -
[ 17.260000] NET: Registered protocol family 10
[ 17.280000] NET: Registered protocol family 8
[ 17.280000] NET: Registered protocol family 20
[ 17.290000] Key type dns_resolver registered
[ 17.310000] RPC: Registered named UNIX socket transport module.
[ 17.310000] RPC: Registered udp transport module.
[ 17.320000] RPC: Registered tcp transport module.
[ 17.320000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 17.370000] tun: Universal TUN/TAP device driver, 1.6
[ 17.380000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 17.390000] l2tp_core: L2TP core driver, V2.0
[ 17.390000] l2tp_netlink: L2TP netlink interface
[ 17.410000] gre: GRE over IPv4 demultiplexor driver
[ 17.410000] ip_gre: GRE over IPv4 tunneling driver
[ 17.500000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 17.510000] gpiodev: gpio device registered with major 251
[ 17.520000] PPP generic driver version 2.4.2
[ 17.530000] nf_conntrack version 0.5.0 (4000 buckets, 16000 max)
[ 17.540000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 17.560000] Netfilter messages via NETLINK v0.30.
[ 17.570000] ip_set: protocol 6
[ 17.610000] Ralink/MTK i2c driver load.
[ 17.620000] Ralink/MTK i2c bus registered.
[ 17.650000] Linux video capture interface: v2.00
[ 17.670000] hidraw: raw HID events driver (C) Jiri Kosina
[ 17.690000] u32 classifier
[ 17.690000] input device check on
[ 17.690000] Actions configured
[ 17.700000] Mirror/redirect action on
[ 17.730000] fuse init (API version 7.22)
[ 17.740000] PandoraBox IP Bandwidth load.
[ 18.130000] PandoraBox MT76x2E AP Driver version-3.0.4.0(Jul 14 2015 13:33:29).
[ 18.230000] PandoraBox MT76x2E AP Driver version-3.0.4.0(Jul 14 2015 13:33:29).
[ 18.270000] arp_tables: (C) 2002 David S. Miller
[ 18.280000] cm109: Keymap for Komunikate KIP1000 phone loaded
[ 18.290000] usbcore: registered new interface driver cm109
[ 18.300000] cm109: CM109 phone driver: 20080805 (C) Alfred E. Heggestad
[ 18.310000] Loading modules backported from Linux version master-2015-06-22-0-g4732c92
[ 18.320000] Backport generated by backports.git backports-20150626-0-gc1a4168
[ 18.330000] gspca_main: v2.14.0 registered
[ 18.340000] usbcore: registered new interface driver gspca_zc3xx
[ 18.350000] ip_tables: (C) 2000-2006 Netfilter Core Team, NAT Type:Symmetric Cone
[ 18.490000] PPP MPPE Compression module registered
[ 18.490000] NET: Registered protocol family 24
[ 18.500000] PPTP driver version 0.8.5
[ 18.510000] usbcore: registered new interface driver Philips webcam
[ 18.520000] rtc-pcf8563 0-0051: chip found, driver version 0.4.3
[ 18.520000] rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable.
[ 18.530000] rtc-pcf8563 0-0051: retrieved date/time is not valid.
[ 18.540000] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
[ 18.550000] usbcore: registered new interface driver ums-alauda
[ 18.560000] usbcore: registered new interface driver ums-cypress
[ 18.570000] usbcore: registered new interface driver ums-datafab
[ 18.580000] usbcore: registered new interface driver ums-freecom
[ 18.590000] usbcore: registered new interface driver ums-isd200
[ 18.600000] usbcore: registered new interface driver ums-jumpshot
[ 18.610000] usbcore: registered new interface driver ums-karma
[ 18.620000] usbcore: registered new interface driver ums-sddr09
[ 18.620000] usbcore: registered new interface driver ums-sddr55
[ 18.630000] usbcore: registered new interface driver ums-usbat
[ 18.650000] usbcore: registered new interface driver usbhid
[ 18.650000] usbhid: USB HID core driver
[ 18.660000] usbcore: registered new interface driver usblp
[ 18.680000] usbcore: registered new interface driver usbserial
[ 18.690000] usbcore: registered new interface driver usbserial_generic
[ 18.690000] usbserial: USB Serial support registered for generic
[ 18.710000] usbcore: registered new interface driver uvcvideo
[ 18.710000] USB Video Class driver (1.1.1)
[ 18.720000] Driver for 1-wire Dallas network protocol.
[ 18.760000] xt_time: kernel timezone is -0000
[ 18.820000] cfg80211: Calling CRDA to update world regulatory domain
[ 18.830000] cfg80211: World regulatory domain updated:
[ 18.830000] cfg80211: DFS Master region: unset
[ 18.840000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 18.840000] usbcore: registered new interface driver ch341
[ 18.840000] usbserial: USB Serial support registered for ch341-uart
[ 18.840000] usbcore: registered new interface driver cp210x
[ 18.840000] usbserial: USB Serial support registered for cp210x
[ 18.850000] usbcore: registered new interface driver dm9601
[ 18.850000] usbcore: registered new interface driver ftdi_sio
[ 18.850000] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 18.890000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.890000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.900000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.910000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 18.920000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 18.930000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 18.940000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.950000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 18.960000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 19.050000] usbcore: registered new interface driver pl2303
[ 19.050000] usbserial: USB Serial support registered for pl2303
[ 19.090000] usbcore: registered new interface driver sierra
[ 19.100000] usbserial: USB Serial support registered for Sierra USB modem
[ 19.120000] usbcore: registered new interface driver snd-usb-audio
[ 19.180000] usbcore: registered new interface driver brcmfmac
[ 19.190000] usbcore: registered new interface driver option
[ 19.200000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 19.210000] usbcore: registered new interface driver qcserial
[ 19.210000] usbserial: USB Serial support registered for Qualcomm USB modem
[ 19.230000] usbcore: registered new interface driver rt2800usb
[ 19.270000] usbcore: registered new interface driver ath9k_htc
[ 19.280000] usbcore: registered new interface driver rtl8192cu
[ 23.730000] raeth: frame engine reset
[ 23.750000] raeth: HW VLAN RX offload enabled
[ 23.750000] raeth: HW VLAN TX offload enabled
[ 23.750000] raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
[ 23.760000] raeth: HW Scatter/Gather TX offload enabled
[ 23.770000] device eth0.1 entered promiscuous mode
[ 23.780000] device eth0 entered promiscuous mode
[ 23.790000] br-lan: port 1(eth0.1) entered forwarding state
[ 23.790000] br-lan: port 1(eth0.1) entered forwarding state
[ 24.400000] EEPROM:Read from [Factory] offset 0x0,length 0x200.
[ 24.480000] EEPROM:Read from [Factory] offset 0x0,length 0x200.
[ 25.790000] br-lan: port 1(eth0.1) entered forwarding state
[ 26.180000] eth0: port 3 link up (1000Mbps/Full duplex)
[ 29.480000] MT76x2E Fast Mode init.
[ 29.500000] EEPROM:Read from [Factory] offset 0x8000,length 0x200.
[ 29.580000] EEPROM:Read from [Factory] offset 0x8000,length 0x200.
[ 31.030000] MT76x2E Fast Mode init.
[ 31.070000] device ra0 entered promiscuous mode
[ 31.070000] br-lan: port 2(ra0) entered forwarding state
[ 31.080000] br-lan: port 2(ra0) entered forwarding state
[ 31.100000] device rai0 entered promiscuous mode
[ 31.110000] br-lan: port 3(rai0) entered forwarding state
[ 31.110000] br-lan: port 3(rai0) entered forwarding state
[ 31.970000] PandoraBox IP bandwidth unload.
[ 31.990000] PandoraBox IP Bandwidth load.
[ 33.080000] br-lan: port 2(ra0) entered forwarding state
[ 33.110000] br-lan: port 3(rai0) entered forwarding state
Разметка
0x000000000000-0x000001000000 : "fullflash"
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "u-boot-env"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000001000000 : "firmware"
0x000000050000-0x00000017ed03 : "kernel"
0x00000017ed03-0x000000fe0000 : "rootfs"
0x000000ec0000-0x000000fe0000 : "rootfs_data"
0x000000fe0000-0x000001000000 : "panic_oops"


Сообщение отредактировал Freize - 05.09.17, 09:27



Реп: (1390)
Прошивку собрал. Работает. Тестируем...



Реп: (1390)
* temamix, согласен как человек который любит трудности и кастомизацию, а как пользователь не согласен. :D

В целом роутер интересный, мне понравилось решение с модулями на pci-e (хотя так конструкция удорожается). Не очень понравилось решение с корпусом, хотя спереди он красивый. Зачем маркировать антенны если они одинаковые? Разъёмы ладно, там хоть чтоб понимать где что у тебя выведено если хочется убрать, например 2.4 и оставить только пятёрку.



Реп: (0)
Подскажите, где скачать прошивку для этого роутера?

Сообщение отредактировал DarkAlo - 17.09.17, 18:39



Реп: (1390)
* DarkAlo, скачать нельзя. У меня есть конфиги для некоторых ревизий данного сабжа, прошивку надо собирать. Пишите в личку посмотрим.



Реп: (18)
Так роутер с какой прошивкой из коробки идет? Пандорабокс? А остальные прошивки openwrt и падаван?
Ну и как работает девайс?
У китайцев на картинки нарисовано что левый pci-e порт поддреживает аж msata. Это правда? Получается там не только тогда USB.
Сата работает и с какой скорость?
Короче интересно было бы почитать обзор его фишек и что как работает. Т.к. девайс интересный но что там на самом деле не понятно.

Сообщение отредактировал Shad0vv - 29.11.17, 08:34



Реп: (0)
А сделать 2WAN + 3LAN в нем можно?
Что бы сделать автоматический failover.



Реп: (1390)
Shad0vv @ 29.11.17, 08:31 *
Так роутер с какой прошивкой из коробки идет?
OpenWRT китайского разлива.
Shad0vv @ 29.11.17, 08:31 *
У китайцев на картинки нарисовано что левый pci-e порт поддреживает аж msata.
У проца есть три pci вывода, два из них в данной плате выведены под pci-e и один на sata весит. Насколько я помню конечно.



Реп: (1390)
Добавил прошивку.



Реп: (4)
Где отзывы владельцев? ;)
Стоит ли покупать этот роутер и почему да/нет?
Какая реальная скорость работы с диском?

Сам же прицениваюсь к полнодуплексному дуалбэнду, но только из-за побаловаться с гпио и сата переплачивать не очень хочется.



Реп: (1390)
chumapda @ 03.02.18, 08:59 *
гпио и сата переплачивать не очень хочется
GPIO в топку, роутер штука не для баловства а для работы. SATA до 50 мб/с выжимать должна. У меня сабжа нету, но если чипы менять не планируете лучше возьмите ZBT 3526.



Реп: (4)
Freize @ 3.02.18, 10:19 *
если чипы менять не планируете лучше возьмите ZBT 3526

дешевле не получается все-равно



Реп: (1390)
* chumapda, зато корпус лучше и с прошивками проблем меньше.



Реп: (0)
с прошивкой padavan перестает видеть кабель, подключенный к порту WAN. Попробовал в kernel-3.4.x.config поменять значения ключей CONFIG_RAETH_ESW_PORT_WAN= и CONFIG_RAETH_ESW_PORT_LAN=..... Какой номер присвою порту WAN, тот порт и перестает определять подключение кабеля.



Реп: (1)
с прошивкой padavan перестает видеть кабель, подключенный к порту WAN

та же самая проблема



Реп: (1390)
* user055,
* DmitrySpb161,
Вопрос, что значит не видит? Не видит в админке, не видит интернет, или что не видит?
Сфотографируйте мне печатную плату, на тестовом образце все работало. Гадать на хофейной гуще я не могу.

Хотя-бы скрины и лог дайте посмотреть.

Сообщение отредактировал Freize - 10.05.18, 09:47



Реп: (0)
Не видит ничего. Для начала не загорается светодиод, показывающий подключение кабеля. В админке тоже не видит. Ну и интернета для кучи нет :)
Логов уже нет, так как прошил openwrt.



Реп: (1390)
* user055, понятно, похоже косяк в конфиге, непонятно только как тестили его так "удачно" или потом ошибка закралась. Исправлю как домой дойду.
Поправлено, попробуйте полностью пересобрать и потестить.

Сообщение отредактировал Freize - 10.05.18, 16:01



Реп: (0)
Заработало. Но... вернул из бэкапа openwrt. Не понимает padavan ntfs. А двухгиговый забитый винчестер форматировать жалко.

Сообщение отредактировал user055 - 11.05.18, 21:43



Реп: (1390)
* user055, прекрасно он понимает, вы просто драйвера включите =)


Полная версия   Текстовая версия

Помощь   Правила

Сейчас: 16.07.24, 19:20