Вобщем после некоторых манипуляций(получения root и попыток разобраться с системой методом препарирования))) получил я
bootloop во всей его красе
балалайка включалась но не загружалась весело поигрывая кольцами))
все попытки допытать своего продавана не увенчались успехом китаец молчал как партизан и отписывался дежурными фразами из разряда "ми связались с компанией производителем и ждем от них ответа, подождите и Вы" ну и растянулось всё это на 1.5 месяца за это время бил во все колокола звонил-писал кому только можно ну и усердно вкуривал 4pda) и тыкал палочкой в reset паралельно
подключая всякие штуковины
, при фотографировании внутренностей магнитолы я обнаружил замечательные выводы rx tx и два gnd, вобщем не долго думая вскрыл
и покуривая мануал на проц подключил
, померил осцилографом скважность пиков нашел частоту 115200, что в принципе било с мануалом, цепанул putty и увидел
такую картину:
--------------------------------------------------------------------------------
Second Boot by Nexell Co. : Ver0.3.6 - Built on Jul 27 2016 16:48:54
--------------------------------------------------------------------------------
DDR3 POR Init Start 0
phy init
Lock value = 166
GATE CYC = 0x00000492
GATE CODE = 0x00000000
Read DQ = 0x08080808
Write DQ = 0x08080808
DDR3 Init Done!
CCI Init!
Wakeup CPU Wakeup Sub CPU 1234567
CPU Wakeup done! WFI is expected.
CPU0 is Master!
Loading from sdmmc...
Image Loading Done!
Launch to 0x42C00000
U-Boot 2014.07-g9d54b6a (Jan 03 2018 - 14:54:24)
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.39 (george@george-K36) (gcc version 4.8 (GCC) ) #1 SMP PREEMPT Wed May 23 19:07:21 CST 2018
[ 0.000000] CPU: ARMv7 Processor [410fd033] revision 3 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: s5p6818
[ 0.000000] nxp_reserve_mem: reserve CMA: size 159100928
[ 0.000000] NXP/CMA: Reserved 0x65e45000/0x097bb000 for 'ion'
[ 0.000000] NXP/CMA: Reserved 0x65e45000/0x097bb000 for 'ion'
[ 0.000000] cma: param: registering early region ion (097bb000@65e45000/00001000)
[ 0.000000] NXP/CMA: success register cma region for 'ion'
[ 0.000000] NXP/CMA: success register cma region for 'ion'
[ 0.000000] cma: param: map: ion-nxp=ion;nx_vpu=ion;
[ 0.000000] rquest persistent memory from 65e41000 (00000000)-00004000
[ 0.000000] Initialized persistent memory from 65e41000-65e44fff
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU : iomap[ 0]: p 0xc0000000 -> v 0xf0000000 len=0x300000
[ 0.000000] CPU : iomap[ 1]: p 0xe0000000 -> v 0xf0300000 len=0x100000
[ 0.000000] CPU : iomap[ 2]: p 0xfff00000 -> v 0xf0400000 len=0x100000
[ 0.000000] CPU : iomap[ 3]: p 0x2c000000 -> v 0xf0500000 len=0x100000
[ 0.000000] CPU : iomap[ 4]: p 0x00000000 -> v 0xf0600000 len=0x100000
[ 0.000000] CPU : DMA Zone Size =16M, CORE 8
[ 0.000000] s5p6818-avn_ref : done board initialize ...
[ 0.000000] CPU : Clock Generator= 58 EA, DVFS = support, PLL.1
[ 0.000000] PLL : [0] = 800000000, [1] = 800000000, [2] = 614394000, [3] = 800000000
[ 0.000000] (0) PLL1: CPU FCLK = 800000000, HCLK = 200000000 (G0)
[ 0.000000] (7) PLL1: CPU FCLK = 800000000, HCLK = 200000000 (G1)
[ 0.000000] (2) PLL3: MEM FCLK = 800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
[ 0.000000] (1) PLL0: BUS BCLK = 400000000, PCLK = 200000000
[ 0.000000] (8) PLL0: CCI4 BCLK = 400000000, PCLK = 200000000
[ 0.000000] (3) PLL0: G3D BCLK = 400000000
[ 0.000000] (4) PLL0: CODA BCLK = 400000000, PCLK = 200000000
[ 0.000000] (5) PLL0: DISP BCLK = 400000000, PCLK = 200000000
[ 0.000000] (6) PLL0: HDMI PCLK = 100000000
[ 0.000000] On node 0 totalpages: 524288
[ 0.000000] free_area_init_node: node 0, pgdat c0780d40, node_mem_map c08dd000
[ 0.000000] DMA zone: 1706 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 192342 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2903 pages used for memmap
[ 0.000000] HighMem zone: 327337 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c1aec000 s7552 r8192 d12928 u32768
[ 0.000000] pcpu-alloc: s7552 r8192 d12928 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519679
[ 0.000000] Kernel command line: console=ttySAC0,115200n8 androidboot.hardware=s5p6818_avn_ref androidboot.console=ttySAC0 androidboot.serialno=0123456789abcdef initrd=0x49000000,0x200000 init=/init lpj=1388544 debug
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] allocated 4194304 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 2048MB = 2048MB total
[ 0.000000] Memory: 1907012k/1907012k available, 190140k reserved, 1320960K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xef800000 - 0xfee00000 ( 246 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef600000 ( 758 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0702000 (7144 kB)
[ 0.000000] .init : 0xc0702000 - 0xc0732d80 ( 196 kB)
[ 0.000000] .data : 0xc0734000 - 0xc0781d40 ( 312 kB)
[ 0.000000] .bss : 0xc0781d64 - 0xc08dceb8 (1389 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] NR_IRQS:272
[ 0.000000] GIC @f0009000: start 0 (gic 31)
[ 0.000000] GPIO @f001a000: start 106, mask 0xffffffff (gpio 85)
[ 0.000000] GPIO @f001b000: start 138, mask 0xffffffff (gpio 86)
[ 0.000000] GPIO @f001c000: start 170, mask 0xffffffff (gpio 87)
[ 0.000000] GPIO @f001d000: start 202, mask 0xffffffff (gpio 88)
[ 0.000000] GPIO @f001e000: start 234, mask 0xffffffff (gpio 89)
[ 0.000000] ALIVE @f0010800: start 266, mask 0x000000ff (alive 36, num 6)
[ 0.000000] timer.0: source, 10000000(HZ:1000), mult:3355443200
[ 0.000000] timer.1: event , 10000000(HZ:1000), mult:42949673
[ 0.000000] sched_clock: 32 bits at 1kHz, resolution 1000000ns, wraps every 4294967295ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop (skipped) preset value.. 2777.08 BogoMIPS (lpj=1388544)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] Mount-cache hash table entries: 512
[ 0.001000] Initializing cgroup subsys debug
[ 0.001000] Initializing cgroup subsys cpuacct
[ 0.001000] Initializing cgroup subsys memory
[ 0.001000] Initializing cgroup subsys freezer
[ 0.001000] CPU: Testing write buffer coherency: ok
[ 0.001000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001000] hw perfevents: no hardware support available
[ 0.001000] Setting up static identity map for 0x4053cc68 - 0x4053ccc0
[ 0.008000] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.014000] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.020000] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.026000] CPU4: thread -1, cpu 0, socket 4, mpidr 80040400
[ 0.032000] CPU5: thread -1, cpu 1, socket 4, mpidr 80040401
[ 0.038000] CPU6: thread -1, cpu 2, socket 4, mpidr 80040402
[ 0.044000] CPU7: thread -1, cpu 3, socket 4, mpidr 80040403
[ 0.044000] Brought up 8 CPUs
[ 0.044000] SMP: Total of 8 processors activated (22216.70 BogoMIPS).
[ 0.045000] devtmpfs: initialized
[ 0.052000] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 3
[ 0.052000] pwm: max = 50000000 hz
[ 0.054000] prepare_gpio_suspend:
[ 0.054000] alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000
[ 0.054000] alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566
[ 0.054000] alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555
[ 0.054000] alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000
[ 0.054000] alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000
[ 0.054000] dummy:
[ 0.054000] NET: Registered protocol family 16
[ 0.055000] persistent_ram: found existing buffer, size 14532, start 4454
[ 0.098000] console [ram-1] enabled
[ 0.099000] [Register machine platform devices]
[ 0.099000] mach: add amba device pl08xdmac.0
[ 0.099000] mach: add amba device pl08xdmac.1
[ 0.099000] mach: add device uart0
[ 0.099000] mach: add device uart1
[ 0.101000] mach: add device uart2
[ 0.103000] mach: add device uart3
[ 0.104000] mach: add device uart4
[ 0.106000] mach: add device uart5
[ 0.108000] mach: add device syncgen [2]
[ 0.108000] mach: add device lvds
[ 0.108000] mach: add device tvout
[ 0.108000] mach: add device i2c bus (array:3)
[ 0.109000] mach: add device Real Time Clock
[ 0.109000] mach: add device generic pwm (array:4)
[ 0.109000] mach: add device generic gpio (array:6)
[ 0.109000] mach: add device i2s (array:2)
[ 0.110000] mach: add device usb_ehci
[ 0.110000] mach: add device usb_ohci
[ 0.110000] mach: add device usb otg
[ 0.110000] mach: add device ion-nxp
[ 0.110000] mach: add graphic device opengl|es
[ 0.110000] mach: add device watchdog
[ 0.110000] [Register board platform devices]
[ 0.111000] plat: add dynamic frequency (pll.1)
[ 0.111000] plat: add device TMU
[ 0.111000] plat: add framebuffer
[ 0.111000] plat: add device sdmmc [2]
[ 0.113000] plat: add device sdmmc [0]
[ 0.115000] plat: add device sdmmc [1]
[ 0.117000] plat: add backlight pwm device
[ 0.117000] plat: add device keypad
[ 0.117000] plat: add device i2c bus(array:5)
[ 0.117000] plat: add device mp8845c ARM
[ 0.118000] plat: add device mp8845c CORE
[ 0.118000] plat: add touch(goodix) device
[ 0.118000] plat: add device asoc-alc5623
[ 0.118000] plat: add device asoc-alc5624
[ 0.118000] plat: add device nxp-v4l2
[ 0.118000] plat: add device hdmi-cec
[ 0.118000]
[ 0.118000] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.119000] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.139000] cma: init: initialising
[ 0.139000] cma: ion: region registered
[ 0.139000] bio: create slab <bio-0> at 0
[ 0.139000] gpiochip_add: registered GPIOs 0 to 31 on device: nxp-gpio.0
[ 0.140000] gpiochip_add: registered GPIOs 32 to 63 on device: nxp-gpio.1
[ 0.140000] gpiochip_add: registered GPIOs 64 to 95 on device: nxp-gpio.2
[ 0.140000] gpiochip_add: registered GPIOs 96 to 127 on device: nxp-gpio.3
[ 0.140000] gpiochip_add: registered GPIOs 128 to 159 on device: nxp-gpio.4
[ 0.141000] gpiochip_add: registered GPIOs 160 to 165 on device: nxp-gpio.5
[ 0.141000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable!
[ 0.141000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels
[ 0.141000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels
[ 0.143000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 33
[ 0.143000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable!
[ 0.143000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels
[ 0.144000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels
[ 0.145000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 34
[ 0.146000] i2c-core: driver [mp8845c] using legacy suspend method
[ 0.146000] i2c-core: driver [mp8845c] using legacy resume method
[ 0.146000] nxp_ion_probe success!!!
[ 0.146000] SCSI subsystem initialized
[ 0.147000] usbcore: registered new interface driver usbfs
[ 0.147000] usbcore: registered new interface driver hub
[ 0.147000] usbcore: registered new device driver usb
[ 0.147000] i2c-gpio i2c-gpio.0: using pins 99 (SDA) and 98 (SCL)
[ 0.148000] i2c-gpio i2c-gpio.3: using pins 48 (SDA) and 50 (SCL)
[ 0.148000] i2c-gpio i2c-gpio.5: using pins 91 (SDA) and 89 (SCL)
[ 0.148000] i2c-gpio i2c-gpio.6: using pins 101 (SDA) and 100 (SCL)
[ 0.153000] MP8845C_1_VOUT: 600 <--> 1449 mV at 1001 mV normal standby
[ 0.155000] i2c-gpio i2c-gpio.8: using pins 66 (SDA) and 65 (SCL)
[ 0.243000] mp8845c 9-001c: failed reading at 0x01
[ 0.243000] mp8845c 9-001c: Fail in pre-initialisation
[ 0.243000] i2c-gpio i2c-gpio.9: using pins 138 (SDA) and 139 (SCL)
[ 0.245000] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.245000] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 0.245000] s3c-i2c s3c2440-i2c.1: bus frequency set to 390 KHz
[ 0.247000] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 0.247000] s3c-i2c s3c2440-i2c.2: slave address 0x10
[ 0.247000] s3c-i2c s3c2440-i2c.2: bus frequency set to 97 KHz
[ 0.248000] Linux media interface: v0.10
[ 0.248000] Linux video capture interface: v2.00
[ 0.248000] dw_mmc dw_mmc.2: Using internal DMA controller.
[ 0.248000] mmc0: no vmmc regulator found
[ 0.250000] dw_mmc dw_mmc.2: Version ID is 250a
[ 0.250000] dw_mmc dw_mmc.2: DW MMC controller at irq 77, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[ 0.250000] dw_mmc dw_mmc.0: Using internal DMA controller.
[ 0.250000] mmc1: no vmmc regulator found
[ 0.250000] dw_mmc dw_mmc.0: Using external card detect irq 150 (io 44)
[ 0.252000] dw_mmc dw_mmc.0: Version ID is 250a
[ 0.252000] dw_mmc dw_mmc.0: DW MMC controller at irq 75, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[ 0.252000] dw_mmc dw_mmc.1: Using internal DMA controller.
[ 0.252000] mmc2: no vmmc regulator found
[ 0.254000] dw_mmc dw_mmc.1: Version ID is 250a
[ 0.254000] dw_mmc dw_mmc.1: DW MMC controller at irq 76, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[ 0.254000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.255000] cfg80211: Calling CRDA to update world regulatory domain
[ 0.255000] Switching to clocksource source timer
[ 0.256000] Clockevents: could not switch to one-shot mode:
[ 0.256000] Clockevents: could not switch to one-shot mode:
[ 0.256000] Clockevents: could not switch to one-shot mode:
[ 0.256000] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
[ 0.256000] Clockevents: could not switch to one-shot mode:
[ 0.256000] Could not switch to high resolution mode on CPU 4
[ 0.256000] dummy_timer is not functional.
[ 0.256000] dummy_timer is not functional.
[ 0.256000] Could not switch to high resolution mode on CPU 6
[ 0.256000] Could not switch to high resolution mode on CPU 5
[ 0.256000] dummy_timer is not functional.
[ 0.256000] Could not switch to high resolution mode on CPU 7
[ 0.256000] Clockevents: could not switch to one-shot mode:
[ 0.256000] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
[ 0.256000] dummy_timer is not functional.
[ 0.256000] Could not switch to high resolution mode on CPU 3
[ 0.256000] Clockevents: could not switch to one-shot mode:
[ 0.256000] Could not switch to high resolution mode on CPU 0
[ 0.256000] dummy_timer is not functional.
[ 0.256000] Could not switch to high resolution mode on CPU 1
[ 0.258000] dummy_timer is not functional.
[ 0.258000] Could not switch to high resolution mode on CPU 2
[ 0.261000] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[ 0.263000] NET: Registered protocol family 2
[ 0.263000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.264000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.266000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.267000] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.267000] TCP: reno registered
[ 0.268000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.268000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.268000] NET: Registered protocol family 1
[ 0.268000] Unpacking initramfs...
[ 0.272000] mmc_host mmc0: device is being hw reset
[ 0.310000] Initramfs unpacking failed: junk in compressed archive
[ 0.312000] Freeing initrd memory: 2048K
[ 0.312000] Disply Reset Status : On
[ 0.313000] Display LVDS register operation
[ 0.313000] Display.0 fps=54 (18 ms), wait=20 jiffies, Pixelclk=43885285hz
[ 0.313000] LVDS: [4]=LVDS connect to [6]=SYNCGEN0
[ 0.313000] Display TVOUT register operation
[ 0.314000] highmem bounce pool size: 64 pages
[ 0.317000] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1)
[ 0.318000] mmc0: new high speed MMC card at address 0001
[ 0.321000] cma: bf: allocator registered
[ 0.323000] NTFS driver 2.1.30 [Flags: R/W DEBUG].
[ 0.324000] fuse init (API version 7.18)
[ 0.324000] msgmni has been set to 1148
[ 0.325000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.325000] io scheduler noop registered (default)
[ 0.326000] io scheduler deadline registered
[ 0.326000] io scheduler cfq registered
[ 0.326000] display.0 connected to fb.0 ...
[ 0.326000] cma: allocate 00258000/ (null) for ion-nxp/ion-nxp
[ 0.326000] cma: allocate 00258000/00001000 from one of ion;nx_vpu=ion
[ 0.326000] cma: allocate 00258000/00001000 from ion
[ 0.327000] cma: init: ion: bf: initialised allocator
[ 0.327000] cma: allocated at 65e45000
[ 0.327000] nxp-fb.0: dma addr = 0x65e45000, buf[0xe50dbac0]
[ 0.327000] cma: allocate 00258000/ (null) for ion-nxp/ion-nxp
[ 0.327000] cma: allocate 00258000/00001000 from one of ion;nx_vpu=ion
[ 0.327000] cma: allocate 00258000/00001000 from ion
[ 0.327000] cma: allocated at 6609d000
[ 0.327000] nxp-fb.0: dma addr = 0x6609d000, buf[0xe50dd140]
[ 0.328000] cma: allocate 00258000/ (null) for ion-nxp/ion-nxp
[ 0.328000] cma: allocate 00258000/00001000 from one of ion;nx_vpu=ion
[ 0.328000] cma: allocate 00258000/00001000 from ion
[ 0.328000] cma: allocated at 662f5000
[ 0.328000] nxp-fb.0: dma addr = 0x662f5000, buf[0xe50dd280]
[ 0.330000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 0.346000] nxp-fb 0: out[0], 1280 * 480 - 32 bpp (phys:65e45000 virt:0xe5e45000 max:7372800)
[ 0.347000] nxp-uart.0: ttySAC0 at MMIO 0xc00a1000 (irq = 39) is a S3C6400/10
[ 0.383000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 0.383000] mmc1: new high speed SDHC card at address 0001
[ 0.394000] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 0.406000] mmc_host mmc2: device is being hw reset
[ 0.422000] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
[ 0.424000] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[ 0.425000] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[ 0.428000] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
[ 0.441000] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 0.443000] mmc2: new high speed SDIO card at address 0001
[ 1.948000] console [ttySAC0] enabled
[ 1.951000] nxp-uart.1: ttySAC1 at MMIO 0xc00a0000 (irq = 38) is a S3C6400/10
[ 1.959000] nxp-uart.2: ttySAC2 at MMIO 0xc00a2000 (irq = 40) is a S3C6400/10
[ 1.966000] nxp-uart.3: ttySAC3 at MMIO 0xc00a3000 (irq = 41) is a S3C6400/10
[ 1.973000] nxp-uart.4: ttySAC4 at MMIO 0xc006d000 (irq = 42) is a S3C6400/10
[ 1.980000] nxp-uart.5: ttySAC5 at MMIO 0xc006f000 (irq = 43) is a S3C6400/10
[ 1.987000] setting PHY_BASEADDR_POWER_GATE, set 1
[ 1.992000] setting PHY_BASEADDR_PMU_ISOLATE+4, set 0
[ 1.997000] setting PHY_BASEADDR_PMU_ISOLATE+8, set 0
[ 2.003000] setting PHY_BASEADDR_PMU_ISOLATE, set 1
[ 2.008000] read PHY_BASEADDR_PMU_ISOLATE + 0xC
[ 2.011000] Wait Power UP Ack(powerUpAck=0x00000000)
[ 2.016000] setting ClockGen, set 1
[ 2.019000] setting Reset VR addr(0xf0012008)
[ 2.025000] setting PHY_BASEADDR_VR_PMU addr(0xf0072000)
[ 2.029000] Vr: VR device driver loaded(ver1.2) for s5p6818
[ 2.038000] loop: module loaded
[ 2.038000] cma: allocate 00077000/00001000 for nx_vpu/nxp-ion
[ 2.043000] cma: allocate 00077000/00001000 from one of ion
[ 2.049000] cma: allocate 00077000/00001000 from ion
[ 2.054000] cma: allocated at 6654d000
[ 2.063000] usbcore: registered new interface driver asix
[ 2.063000] usbcore: registered new interface driver cdc_ether
[ 2.069000] usbcore: registered new interface driver net1080
[ 2.074000] usbcore: registered new interface driver rndis_host
[ 2.080000] usbcore: registered new interface driver zaurus
[ 2.086000] usbcore: registered new interface driver ipheth
[ 2.091000] usbcore: registered new interface driver cdc_ncm
[ 2.097000] xin100: 10-Jan-2015 xin_ncm_init, HZ = 1000
[ 2.102000] usbcore: registered new interface driver xin_ncm
[ 2.108000] [xin_init] init xin com driver
[ 2.112000] [xin_init] xin_tty_driver is 0xe5ada240
[ 2.116000] usbcore: registered new interface driver xin_hid
[ 2.122000] Linux Virtual COM Driver v1.0
[ 2.126000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.133000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller
[ 2.139000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1
[ 2.146000] nxp-ehci nxp-ehci: irq 82, io mem 0xc0030000
[ 2.157000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00
[ 2.157000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.163000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.170000] usb usb1: Product: SLsi Synopsys EHCI Host Controller
[ 2.176000] usb usb1: Manufacturer: Linux 3.4.39 ehci_hcd
[ 2.182000] usb usb1: SerialNumber: nxp-ehci
[ 2.186000] hub 1-0:1.0: USB hub found
[ 2.190000] hub 1-0:1.0: 3 ports detected
[ 2.194000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 2.498000] usb 1-1: new high-speed USB device number 2 using nxp-ehci
[ 2.549000] Core Release: 2.93a
[ 2.549000] Setting default values for core params
[ 2.551000] Finished setting default values for core params
[ 2.614000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 2.615000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.622000] usb 1-1: Product: USB2.0 Hub
[ 2.627000] hub 1-1:1.0: USB hub found
[ 2.630000] hub 1-1:1.0: 4 ports detected
[ 2.907000] Using Buffer DMA mode
[ 2.907000] Dedicated Tx FIFOs mode
[ 2.908000] NOT SUPPORTED IN HOST MODE
[ 2.912000] dwc_otg: Microframe scheduler enabled
[ 2.916000] dwc_otg dwc_otg: DWC OTG Controller
[ 2.921000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2
[ 2.928000] dwc_otg dwc_otg: irq 81, io mem 0x00000000
[ 2.933000] Init: Port Power? op_state=1
[ 2.940000] Init: Power Port Complete!!!
[ 2.941000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.947000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.955000] usb usb2: Product: DWC OTG Controller
[ 2.959000] usb usb2: Manufacturer: Linux 3.4.39 dwc_otg_hcd
[ 2.965000] usb usb2: SerialNumber: dwc_otg
[ 2.969000] hub 2-0:1.0: USB hub found
[ 2.973000] hub 2-0:1.0: 1 port detected
[ 2.977000] dwc_otg: FIQ disabled
[ 2.980000] dwc_otg: NAK holdoff enabled
[ 2.984000] dwc_otg: FIQ split fix disabled
[ 2.988000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.994000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller
[ 3.000000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3
[ 3.007000] nxp-ohci nxp-ohci: irq 82, io mem 0xc0020000
[ 3.070000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.071000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.078000] usb usb3: Product: SLsi Synopsys OHCI Host Controller
[ 3.084000] usb usb3: Manufacturer: Linux 3.4.39 ohci_hcd
[ 3.089000] usb usb3: SerialNumber: nxp-ohci
[ 3.094000] hub 3-0:1.0: USB hub found
[ 3.097000] hub 3-0:1.0: 3 ports detected
[ 3.102000] Initializing USB Mass Storage driver...
[ 3.106000] usbcore: registered new interface driver usb-storage
[ 3.112000] USB Mass Storage support registered.
[ 3.117000] usbcore: registered new interface driver usbserial
[ 3.122000] usbcore: registered new interface driver usbserial_generic
[ 3.129000] USB Serial support registered for generic
[ 3.134000] usbserial: USB Serial Driver core
[ 3.138000] usbcore: registered new interface driver cp210x
[ 3.144000] USB Serial support registered for cp210x
[ 3.149000] usbcore: registered new interface driver option
[ 3.154000] USB Serial support registered for GSM modem (1-port)
[ 3.161000] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 3.167000] android_usb gadget: Number of LUNs=1
[ 3.172000] lun0: LUN: removable file: (no medium)
[ 3.177000] android_usb gadget: android_usb ready
[ 3.181000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0
[ 3.189000] [RTC] day=2009.09.01 time=00:00:00
[ 3.193000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0
[ 3.199000] i2c /dev entries driver
[ 3.203000] i2c-core: driver [tw9992] using legacy suspend method
[ 3.208000] i2c-core: driver [tw9992] using legacy resume method
[ 3.214000] nxp_v4l2_probe entered
[ 3.218000] srv360_probe entered
[ 3.222000] create_nxp_out
[ 3.224000] create_nxp_resc
[ 3.226000] register_nxp_out
[ 3.230000] register_nxp_resc
[ 3.232000] nxp_edid_init
[ 3.235000] _edid_i2c_probe
[ 3.238000] nxp_edid_init: success!!!
[ 3.241000] nxp_hdmiphy_init
[ 3.246000] nxp_hdmi_cec_probe success
[ 3.248000] nxp_wdt: NXP Watchdog Timer, (c) 2014 SLsiAP
[ 3.257000] nxp-wdt nxp-wdt: watchdog inactive, reset disabled, irq disabled
[ 3.261000] device-mapper: uevent: version 1.0.3
[ 3.265000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 3.273000] DVFS: ASV[2] IDS 17mA, Ro 129 -> Table [IDS 15mA, Ro 130]
[ 3.279000] ASV 0 = 1400000khz, 1275000 uV
[ 3.284000] ASV 1 = 1300000khz, 1225000 uV
[ 3.288000] ASV 2 = 1200000khz, 1175000 uV
[ 3.293000] ASV 3 = 1100000khz, 1125000 uV
[ 3.297000] ASV 4 = 1000000khz, 1100000 uV
[ 3.301000] ASV 5 = 900000khz, 1075000 uV
[ 3.306000] ASV 6 = 800000khz, 1050000 uV
[ 3.310000] ASV 7 = 700000khz, 1025000 uV
[ 3.315000] ASV 8 = 600000khz, 1000000 uV
[ 3.319000] ASV 9 = 500000khz, 1000000 uV
[ 3.323000] ASV 10 = 400000khz, 1000000 uV
[ 3.329000] DVFS: regulator vdd_arm_1.3V
[ 3.332000] DVFS: cpu DVFS with PLL.1 [tables=11]
[ 3.337000] cpuidle: using governor ladder
[ 3.340000] cpuidle: using governor menu
[ 3.344000] mmcblk0: mmc0:0001 AJNB4R 14.5 GiB
[ 3.349000] mmcblk0boot0: mmc0:0001 AJNB4R partition 1 4.00 MiB
[ 3.355000] mmcblk0boot1: mmc0:0001 AJNB4R partition 2 4.00 MiB
[ 3.362000] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 >
[ 3.368000] mmcblk0boot1: unknown partition table
[ 3.371000] mmcblk0boot0: unknown partition table
[ 3.375000] mmcblk1: mmc1:0001 SD 7.44 GiB
[ 3.380000] mmcblk1: p1
[ 3.381000] Synopsys Designware Multimedia Card Interface Driver
[ 3.389000] usbcore: registered new interface driver usbhid
[ 3.393000] usbhid: USB HID core driver
[ 3.397000] ashmem: initialized
[ 3.400000] logger: created 256K log 'log_main'
[ 3.404000] logger: created 256K log 'log_events'
[ 3.409000] logger: created 256K log 'log_radio'
[ 3.413000] logger: created 256K log 'log_system'
[ 3.419000] snd pcm: register sound platform 'nxp-pcm'
[ 3.424000] snd i2s: ch 0, master, iis mode, 48000(47999)hz, 32 FBITs, MCLK=12287880hz, RFS=256
[ 3.433000] snd i2s: ch 1, master, iis mode, 48000(47999)hz, 32 FBITs, MCLK=12287880hz, RFS=256
[ 3.440000] alc5623-dai: register card alc5621-hifi -> nxp-i2s.0
[ 3.446000] alc5624-dai: register card alc5621-hifi -> nxp-i2s.1
[ 3.452000] GACT probability NOT on
[ 3.456000] Mirror/redirect action on
[ 3.459000] u32 classifier
[ 3.462000] Actions configured
[ 3.465000] Netfilter messages via NETLINK v0.30.
[ 3.470000] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 3.476000] ctnetlink v0.93: registering with nfnetlink.
[ 3.481000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 3.488000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 3.494000] xt_time: kernel timezone is -0000
[ 3.499000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.504000] arp_tables: (C) 2002 David S. Miller
[ 3.508000] TCP: cubic registered
[ 3.511000] Initializing XFRM netlink socket
[ 3.516000] NET: Registered protocol family 10
[ 3.520000] Mobile IPv6
[ 3.522000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.528000] IPv6 over IPv4 tunneling driver
[ 3.533000] NET: Registered protocol family 17
[ 3.536000] NET: Registered protocol family 15
[ 3.541000] NET: Registered protocol family 35
[ 3.545000] 8021q: 802.1Q VLAN Support v1.8
[ 3.549000] lib80211: common routines for IEEE802.11 drivers
[ 3.555000] lib80211_crypt: registered algorithm 'NULL'
[ 3.560000] lib80211_crypt: registered algorithm 'WEP'
[ 3.565000] lib80211_crypt: registered algorithm 'CCMP'
[ 3.570000] lib80211_crypt: registered algorithm 'TKIP'
[ 3.576000] Registering the dns_resolver key type
[ 3.580000] Registering SWP/SWPB emulation handler
[ 3.585000] nxp-rtc nxp-rtc.0: setting system clock to 2009-09-01 00:00:01 UTC (1251763201)
[ 3.594000] tmu[0] = trim 38:0, ret 1
[ 3.597000] TMU: register tmu.0 to hwmon (max 1400000khz)
[ 3.612000] init: /init.s5p6818_avn_ref.rc: 413: ignored duplicate definition of service 'ril-daemon'
[ 3.699000] init: /dev/hw_random not found
[ 3.739000] init: /dev/hw_random not found
[ 3.740000] ====> ext4_mount
[ 3.764000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.766000] fs_mgr: __mount(source=/dev/block/platform/dw_mmc.2/by-num/p2,target=/system,type=ext4)=0
[ 3.776000] ====> ext4_mount
[ 3.807000] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 3.812000] fs_mgr: check_fs(): mount(/dev/block/platform/dw_mmc.2/by-num/p3,/cache,ext4)=0
[ 3.848000] fs_mgr: Running /system/bin/e2fsck on /dev/block/platform/dw_mmc.2/by-num/p3
[ 3.942000] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 3.942000] e2fsck: /dev/block/platform/dw_mmc.2/by-num/p3: clean, 20/33600 files, 4341/134144 blocks
[ 3.951000] ====> ext4_mount
[ 3.964000] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[ 3.969000] fs_mgr: __mount(source=/dev/block/platform/dw_mmc.2/by-num/p3,target=/cache,type=ext4)=0
[ 3.978000] ====> ext4_mount
[ 4.053000] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 4.058000] fs_mgr: check_fs(): mount(/dev/block/platform/dw_mmc.2/by-num/p7,/data,ext4)=0
[ 4.090000] fs_mgr: Running /system/bin/e2fsck on /dev/block/platform/dw_mmc.2/by-num/p7
[ 4.174000] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 4.174000] e2fsck: /dev/block/platform/dw_mmc.2/by-num/p7: clean, 5358/848640 files, 686426/3390070 blocks
[ 4.183000] ====> ext4_mount
[ 4.198000] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[ 4.203000] fs_mgr: __mount(source=/dev/block/platform/dw_mmc.2/by-num/p7,target=/data,type=ext4)=0
[ 4.227000] init: mcu_ldisc start
[ 4.228000] init: TIOCSETD error 0
[ 4.298000] binder: 107:107 transaction failed 29189, size 0-0
[ 4.337000] _enable_tvout: enable tvout
[ 4.407000] init: untracked pid 162 exited with status 0
CANNOT LINK EXECUTABLE DEPENDENCIES: library "libcrypto.so" not found
CANNOT LINK EXECUTABLE DEPENDENCIES: [ 4.441000] _card_instantiate entered
library "libcrypto.so" not found
[ 4.448000] _card_instantiate entered
@android:/ # [ 4.459000] init: untracked pid 166 exited with status 0
[ 4.463000] warning: `daemonsu' uses 32-bit capabilities (legacy support in use)
[ 4.465000] asoc: alc5621-hifi <-> nxp-i2s.1 mapping ok
[ 4.467000] _card_instantiate exit
[ 4.479000] init: untracked pid 163 exited with status 0
[ 4.548000] logd.auditd: start
[ 4.549000] asoc: alc5621-hifi <-> nxp-i2s.0 mapping ok
[ 4.552000] _card_instantiate exit
[ 4.564000] init: untracked pid 189 exited with status 0
[ 4.877000] tw9992_link_setup
[ 4.877000] tw9992 0-003d: tw9992_init_formats:
[ 4.879000] srv360_s_power: 1
[ 4.882000] tw9992 0-003d: tw9992_s_power() on:1
[ 4.886000] tw9992 0-003d: tw9992_init_parameters:
[ 4.891000] srv360_s_power: 1
[ 4.894000] tw9992 0-003d: tw9992_s_power() on:1
[ 4.899000] tw9992 0-003d: tw9992_init_parameters:
[ 4.994000] cma: allocate 00152000/ (null) for ion-nxp/ion-nxp
[ 4.994000] cma: allocate 00152000/00001000 from one of ion;nx_vpu=ion
[ 5.001000] cma: allocate 00152000/00001000 from ion
[ 5.006000] cma: allocated at 665c4000
[ 5.094000] cma: allocate 00152000/ (null) for ion-nxp/ion-nxp
[ 5.094000] cma: allocate 00152000/00001000 from one of ion;nx_vpu=ion
[ 5.095000] nxp_mlc_set_crop: pad(0), crop(0,0,720,480)
[ 5.095000] nxp_mlc_s_stream: enable 1, client VIDEO MLC RGB1, is_video 0
[ 5.095000] _hw_configure_rgb 1: code(0x86530000), w(720), h(480), pixelbyte(4)
[ 5.095000] _hw_configure_rgb 1 crop(0:0:720:480)
[ 5.095000] _hw_rgb_enable: module 1, enable 1
[ 5.095000] Fail, SYNCGEN1 not set sync ...
[ 5.133000] cma: allocate 00152000/00001000 from ion
[ 5.138000] cma: allocated at 66716000
[ 5.152000] cma: allocate 00258000/ (null) for ion-nxp/ion-nxp
[ 5.152000] cma: allocate 00258000/00001000 from one of ion;nx_vpu=ion
[ 5.158000] cma: allocate 00258000/00001000 from ion
[ 5.163000] cma: allocated at 66868000
[ 5.196000] tvout_enable exit
[ 5.196000] nxp_tvout_s_stream: 1
[ 5.196000] Fail, SYNCGEN1 not set sync ...
[ 5.201000] tvout_enable exit
[ 5.239000] cma: allocate 00258000/ (null) for ion-nxp/ion-nxp
[ 5.239000] cma: allocate 00258000/00001000 from one of ion;nx_vpu=ion
[ 5.249000] cma: allocate 00258000/00001000 from ion
[ 5.251000] cma: allocated at 66ac0000
[ 5.302000] healthd: No charger supplies found
[ 5.302000] healthd: No battery devices found
напрягли меня тут конкретно вот эти строки
CANNOT LINK EXECUTABLE DEPENDENCIES: library "libcrypto.so" not found
CANNOT LINK EXECUTABLE DEPENDENCIES: [ 4.441000] _card_instantiate entered
library "libcrypto.so" not found
при попытке запустить любой бинарь получал тот же самый отлуп(
был сделан вывод о том что ФС полегла, соответственно ни один бинарь не запускается по системе гулять не могу(
грусть-печаль, однако) нам доступен U-Boot!
полазил я по U-Boot из путного-поработал с флешкой и получил
вот такие переменные окружения:
s5p6818# printenv
baudrate=115200
bootcmd=ext4load mmc 2:1 0x48000000 uImage;ext4load mmc 2:1 0x49000000 root.img.gz;bootm 0x48000000
bootdelay=0
bootfile=uImage
ethaddr=00:e2:1c:ba:e8:60
fastboot=#sd0partitionmap#flash=<device>.<devno>:<partition>:<fstype>:<start>,<length>:filename#supportdevice:eeprom,nand,mmc#supportfstype:2nd,boot,raw,fat,ext4,ubi#flash=mmc,2:2ndboot:2nd:0x200,0x8e00:2ndboot.bin;flash=mmc,2:bootloader:boot:0x8000,0x77000:u-boot.bin;flash=mmc,2:boot:ext4:0x000100000,0x004000000:boot.img;flash=mmc,2:system:ext4:0x4100000,0x40000000:system.img;flash=mmc,2:cache:ext4:0x44900000,0x20C00000:cache.img;flash=mmc,2:misc:emmc:0x65600000,0x800000:misc.img;flash=mmc,2:recovery:emmc:0x66100000,0x1600000:recovery.img;flash=mmc,2:userdata:ext4:0x67A00000,0x0:userdata.img;
filesize=119438
gatewayip=192.168.1.254
ipaddr=192.168.1.165
netmask=255.255.255.0
serverip=192.168.1.164
stderr=serial
stdin=serial
stdout=serial
кстати вход в U-Boot по нажатию клавиши ENTER до загрузки ядра
попечалился я и сгоря набрал в шеле загруженного андроида
"reboot recovery"
ну и собственно экран погас, нарисовалось тело убитого робота и в консоле весело загорелась решеточка)))
при этом доступен busybox и полностью вся память MMC производства NXP)
прикинув пальцы к носу накидал
скриптец:
mount /dev/block/mmcblk0p2 /system&&mount /dev/block/platform/dw_mmc.0/mmcblk1p1 /sdcard&&/system/xbin/tar --overwrite -xvf /sdcard/update.tar -C /system&&umount sdcard&&umount /system
предварительно распотрошив в Ubunt'e файл update.zip, удалив из него все лишнее и оставив бинари, либы да настройки
вот он: если что), залил его на SDCard вставил её перезагрузил в reboot recovery после чего набрал скрипт
ну и скрестив пальцы нажал "ENTER" строчки весело побежали по экрану ФС была переписана, НО при загрузке появилась куча сообщений типа "Permition denied!" на бинари из дирректорий /bin, /xbin
хорошенько ругнувшись накидал
еще один скрипт:
cd /system/xbin/&&busybox chmod 755 *&&cd /system/bin/&&busybox chmod 755 *
нажал "ENTER", дождался перезагрузки и получил
чего и Вам желаю, вобщем чуть позже уже без эмоций напишу небольшую шпаргалку) и подниму в голову.
Сообщение отредактировал -=RaY=- - 05.09.22, 19:59